Question about Televison & Video

1 Answer

Sanyo tv chassis 2111 Series EB5-W Dead

Front light comes on, then flashes three times and just keeps flashing three times

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 149 Answers

Hi there, light flashes means a shorted parts at the power supply and mostly at the horrizontal sec,, it may need to check-up and repair., do some testing and check-up at the horrizontal section. ty

Posted on Mar 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

While watching tv, there was a faint "pop" and the tv went dead. it will not turn on by front buttons or remote.

Does the power indicating flash three times then go out when power is pressed? If so you may need a deflection board which is famous for problems with the ITC222 chassis.

May 02, 2011 | RCA HD52W59 HDTV Projection Television

1 Answer

My sanyo tv stand by light keeps flashing and it wont turn on can you tell me whats up with it

i have 32inch sanyo tv i have blue light on front whitch comes on when on stand by it wount come of standby eney idears on how mutch it will cost to get fixed x

Nov 13, 2010 | Sanyo PDP-42H2W 42 in. HD-Ready Plasma...

3 Answers

Sanyo DP52449, tv getting power but no display

When DP52449 (chassis 01 - that is important!) does not power on and the front LED flashes every 15-20 seconds you have a faulty main board, which you need to replace or get serviced.

We presently do not offer replacement boards, but we do offer repair services for them at

You may also be curious to read the article we wrote back in July 2012 on a problem that sounds exactly like yours and which lead to the service offerring:

Hope this helps!

Feb 20, 2010 | Sanyo DP32746 32 in. LCD Television

1 Answer

Panasonic PT-47WX42F does not come on light flashes 3 times HELP!

There is a service manual which should cover this model/chassis series:

Elektrotanya for electronics experts

(PDF format - free - no sign-up needed - 100% clean)

Page 11 ('auto diagnosis feature') shows a table of LED flashes and what each one means. I'd start by checking D-board (since that is power and deflection) and going from there.

Dec 21, 2017 | Televison & Video

3 Answers

Flashing timer light, cannot turn on tv

Press and hold "Device" and "Menu" buttons for six seconds and see if you then get a patter of flashes pertaining to the error codes... I would suspect one of the following codes:
12 No Error Detected
22 Recovery From Momentary Reset
32 Lamp Cover Open
33 Air Filter Cover Open
34 Lamp Abnormality
35 Chassis Fan Failure
36 Exhaust (Back Cover) Or Lamp Ballast Fan Failure
37 Engine (Dmd Or Lamp) Fan Failure
38 Excess Lamp Temperature
39 Excess Dmd Temperature
41 Short Detected
44 Dvi Cable (Between Chassis And Engine) Disconnected

Sep 26, 2008 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Timer light will not go off and I cannot turn on TV

Are you asking about the wd62525? If so that's a v26 chassis and equipped with a self diagnostic test by flashing a series of two digit sequence after depressing the power button. After depressing the power button count the number of flashes - then you'll see a slight pause - then another series of flashes. (for example: four flashes, pause and four more flashes is an error code 44). The unit repeats this coding at least three times so be as accurate as possible...

Sep 26, 2008 | Televison & Video

2 Answers

Won't come on

hy i got a toshiba 42" LCD tv ,when i press the power boton
iget the red light,& it stay that way ontil i pressthe power back off
thanks for any help

Jun 26, 2008 | Toshiba 62HM95 62" HDTV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74990 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Cindy Wells

Level 3 Expert

5297 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides