Question about Sharp AR-M160 Laser Printer

1 Answer

Printer Letter "H" and number "4" appears in the display. On turning off the power switch and waiting for 10 seconds and then turning on the switch again, does not clear the message "H" and "4"

Posted by on

  • Anonymous Jun 09, 2008

    We did lose power last night and now the printer is flashing a h and a 4 and we can't get it to stop. We shut the machine down and turned it back on but that did not solve our problem.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,072 Answers

Give this a try, 9 times out of 10 it fixes the H4 problem.

> Support & Drivers > WorkCentre XD100 Digital Copier - Laser Printer Support > How To Clear an H4 Code Solution: Perform a Fault Reset 14 printer - bttn_print.gifMake Printable Email this page Performing a Fault Reset 14 will reset your WorkCentre and will help to clear error codes.

  1. Find the pink Clear button on the Control Panel of the WorkCentre.
  2. Find the button below the word Auto.
  3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto] NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
  4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
  5. Press the green [Start] button.
  6. Press the pink [Clear] button two times.
  7. The WorkCentre should now warm up and come to ready.
  8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.

Posted on Mar 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix error code 3501


if the code does come back DO NOT RESET the machine again! It is indicating a problem the code you are resetting is the fuser and it can catch on fire! That will ruin a perfectly good day!!!
ENSURE YOU WAIT 10 SECONDS

1.
Turn OFF the main power switch. (Located inside machine) Leave control power switch in the on position.)
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.

Jun 14, 2016 | Konica Minolta Bizhub 501 Copier

1 Answer

Error c3102


The code indicates that the fuser is not turning for whatever reason

Oct 06, 2015 | Printers & Copiers

2 Answers

Error C3102


The Fuser is not turning... follow these steps
1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key. Keep holding it till the T reset appears
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, wait 10 seconds and turn the machine back on, this should reset the service code and with any luck the machine will run!

May 03, 2014 | Konica Minolta Bizhub C451 Copy-print-scan

1 Answer

I tried to remove a paper from the paper tray while printing a fax then the printer displayed the following massage: printer errorhas occured and the number 5200


Please reset the printer

1. Turn off your printer
2. Press and hold the STOP/RESET button
3. Press and hold Power ON button
4. While holding the Power ON button, release the STOP/RESET button
5. While holding still the Power ON button, press twice the STOP/RESET button
6. Release the Power ON button
7. Wait until it display an "idle" message. It will take about a minute.
8. When "idle" appear, open the top cover to expose the cartridges.
9. Lift up the cover for cartridge holder and take out both the black and color cartridges
10. Return the cover of cartridge holder and turn off the printer
11. Return the top cover and turn on the printer again
12. After the printer initialize, return the cartridges.

1. Press and Hold the STOP/RESET button and wait until it self restart.
2. Release the STOP/RESET button the the printer is restarting.
3. Wait for a few seconds

Apr 25, 2011 | Canon PIXMA MX320 Color USB InkJet Printer

1 Answer

Shows error code C-3102 and will not do any operation


The code indicates that the fuser is not turning for whatever reason...... Do the following if it resets the code great, if it comes back it's probably the sensor on the fuser that detects rotation. They have had problems with the mounting plate but at any rate at that point it would be time to call your servicing company.
Here is the reset procedure:
1.
Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key. Keep holding it till the Trouble reset appears
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, wait 10 seconds and fire the machine back up, this should reset the service code and with any luck the machine will run!

Dec 28, 2010 | Minolta C350 Color Printer/Scanner/Copier

1 Answer

Getting error code C11A4 can you help me fix this please?


Some basic reset procedures.

A. Open and close the front door.
B. Power off the machine, wait 30 seconds power on.
C. Power down the machine, unplug from the wall for 1 minute, plug in and power on.

D. 13.1 Trouble resetting
1. Turn OFF the Main Power Switch.

2. Turn Main Power Switch ON again while pressing the Utility/Counter key more than 10 seconds after.

3. Touch [Trouble Reset].

4. Check to make sure that [OK] is displayed and the it has been reset.

5. Turn off the Main Power Switch and turn it on again more than 10 seconds after, and make sure that the machine properly starts.

Nov 19, 2010 | Konica Minolta bizhub 250 All-In-One Laser...

1 Answer

Canon Printer MX328 displaying message "Printer Error has Occured 5200". What does this indicate


Please reset the printer

1. Turn off your printer
2. Press and hold the STOP/RESET button
3. Press and hold Power ON button
4. While holding the Power ON button, release the STOP/RESET button
5. While holding still the Power ON button, press twice the STOP/RESET button
6. Release the Power ON button
7. Wait until it display an "idle" message. It will take about a minute.
8. When "idle" appear, open the top cover to expose the cartridges.
9. Lift up the cover for cartridge holder and take out both the black and color cartridges
10. Return the cover of cartridge holder and turn off the printer
11. Return the top cover and turn on the printer again
12. After the printer initialize, return the cartridges.

1. Press and Hold the STOP/RESET button and wait until it self restart.
2. Release the STOP/RESET button the the printer is restarting.
3. Wait for a few seconds

Oct 26, 2010 | Canon PIXMA MX300 All-in-One Printer

1 Answer

Error code 501 solution


To clear error 5100 clean the surface of the copper contact of the ink cartridges with a moistened cloth and let it air dry. Fix the cartridges to the holder and return properly the cover of the printer.

These 2 reset procedures will help you clear the errors displaying in the control panel of the printer and let you print again.

To clear U053, U051 and U052
1. Turn off your printer
2. Press and hold the STOP/RESET button
3. Press and hold Power ON button
4. While holding the Power ON button, release the STOP/RESET button
5. While holding still the Power ON button, press twice the STOP/RESET button
6. Release the Power ON button
7. Wait until it display an "idle" message. It will take about a minute.
8. When "idle" appear, open the top cover to expose the cartridges.
9. Lift up the cover for cartridge holder and take out both the black and color cartridges
10. Return the cover of cartridge holder and turn off the printer
11. Return the top cover and turn on the printer again
12. After the printer initialize, return the cartridges.

To clear error U162 or U163
1. Turn off your printer an turn it on again
2. After the printer initialize try to copy or print. The error will appear.
3. When the error is displayed on the display panel of the printer, Press and Hold the STOP/RESET button and wait until it self restart.
4. Release the STOP/RESET button the the printer is restarting.
5. Wait for a few seconds and the pending print jobs will commence.




Aug 10, 2010 | Canon PIXMA MP180 All-In-One InkJet...

2 Answers

Mx328 disable check ink how to do this or disable ink low


To disable ink low detection, do this steps:
1. Turn off your printer
2. Press and hold the STOP/RESET button
3. Press and hold Power ON button
4. While holding the Power ON button, release the STOP/RESET button
5. While holding still the Power ON button, press twice the STOP/RESET button
6. Release the Power ON button
7. Wait until it display an "idle" message. It will take about a minute.
8. When "idle" appear, open the top cover to expose the cartridges.
9. Lift up the cover for cartridge holder and take out both the black and color cartridges
10. Return the cover of cartridge holder and turn off the printer
11. Return the top cover and turn on the printer again
12. After the printer initialize, return the cartridges.

To disable detection of reused cartridge, do this step:
1. Turn off your printer an turn it on again
2. After the printer initialize try to copy or print. The error will appear.
3. When the error is displayed on the display panel of the printer, Press and Hold the STOP/RESET button and wait until it self restart.
4. Release the STOP/RESET button the the printer is restarting.
5. Wait for a few seconds and the pending print jobs will commence

Please find the complete explanation in my tips in this link
http://www.fixya.com/support/r5191523-canon_pixma_mx320_disable_ink_cartridge

May 20, 2010 | Printers & Copiers

1 Answer

Probleme de fonctionnement SC546


Check,clean and measurement the continuity of the fusing unit parts(heater lamps,thermistors,thermofuses) and reset the trouble code.Enter in the service mode :press total clear (yellow)key-107-and press and hold the clear (red)key more 4 second.If the SP mode appears to the display press the windows,open the front door and turn OFF the main power switch.Unplugged the machine,wait 10 seconds ,plugged on ,closed the front door and turn ON the power switch.

Oct 06, 2009 | Ricoh Printers & Copiers

Not finding what you are looking for?
Sharp AR-M160 Laser Printer Logo

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Printers & Copiers Experts

George Mclaughlin

Level 2 Expert

330 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Vito Suglio

Level 1 Expert

23 Answers

Are you a Sharp Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...