Question about PC Desktops

1 Answer

Proview 700p monitor computer wont boot up getting error beep .reconect my old monitor boots up ok

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 34 Answers

My be a compatibilty issue with your bios . try to update bios and then try .

Vote for me .

Posted on Mar 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My pc beeps when stars and the does not start completly it continues to give that beeping and the monitor does not display anything


The beeps in your computer at boot up mean that there is an hardware.
Every number and lenght of beep is a code that indicates where the error is. You should refer to your producers webpage to "translate" the code in the cause of boot failure

Feb 06, 2013 | HP PC Desktops

1 Answer

Asus p5lp-le no display


If it seems like the computer completed the boot process but the screen is blank, try the steps below.

The problem will either be the monitor or the video card inside the computer. Connect another monitor to the computer to isolate the problem. Borrow a monitor from a neighbor, friend, relative or co-worker and connect it to the computer. If the Borrowed monitor displays and works ok, then your original monitor is bad and the video card is good. If the Borrowed monitor does not work then the video card inside the computer is bad.

If the computer did not complete the boot process then try the steps below.

When you plug in the power cord is there any lights whatsoever on the laptop, where the plug goes in or on the AC Adapter of the power cord?

When you press the power button do you hear fans running, hard drive spinning, lights on the computer, hear any beeps or lights constantly blinking, hear the DvD/CD drive click and the light on the drawer of the DvD/CD turn on for a second or two? If so the computer is trying to boot or may have booted, but the screen is not showing for some reason.

Beep tones and blinking lights tells the technicians what is going on with the laptop and why it is not booting. Most times it's a motherboard issue when you hear beeps or blinking lights continuous. Most times the problem is with the memory or Video Card. Count the Blinking Lights or Beeps and take note of their pattern (1 Long or 1 Long followed by 2 Short).

Maybe you have a Static Charge Buildup. Remove the Power Cord, then Press and Hold the power button for 30 seconds. After 30 seconds plug the power cord back in and hit the power button to see if it boots.

Maybe your memory is bad or the memory slot is bad.

Remove the Power Cord, Open the Case and remove one of the memory chips. Set the chip aside then try rebooting the computer. If it boots, then you know the memory chip you set aside is bad so mark an x on it with an ink pen. If it fails to boot then move the chip to the next memory slot and try rebooting. If it fails take the chip out and set it aside, then put the other chip in and try booting it in both slots. If it boots, just to verify that the chip set aside is bad, mark an x on it and put it into the open memory chip slot and try booting.

Jun 05, 2012 | ASUS PC Desktops

1 Answer

My Dell XPS 730 needed a new CMOS battery I changed this but now it wont post get no beep errors and it doesn't get to the DELL screen. There is power everything lights up and fans start going but no...


I believe you have used the wrong type of CMOS battery. Try putting the old one back in and see if it will boot. If not the CMOS NAND chip may be broken. If this is the case contact Dell and order a new one.

May 07, 2011 | Dell XPS 730X Desktop Computer

2 Answers

When i turn my computer on it has a long beep sound and then another long beep and wont quit... please help


Check your MEMORY MODULES . Try removing them, cleaning them with rubbing alcohol and the reinstalling them. Re-boot. That should work, ok?

Oct 18, 2010 | Acer PC Desktops

2 Answers

Computer wont boot up


you need to refix the RAM sticks and restart your pc. IF the problem persists change the RAM slots and put RAM sticks one by one in different slots, then restart your pc it will work

Feb 15, 2010 | Gateway GT5220 PC Desktop

1 Answer

Computer "turns on" i hear four to five beeps, but the monitor gets no signal. a friend gave me the computer, only once did i see it boot up fully but it froze up so i had to restart it and it wont work....


Without knowing the exact frequency/length of the beeps my first guess would be a bad stick of ram or a bad video card. If there is more than one stick of ram in the computer try it with one of the sticks pulled, pulling each stick until it does boot. if it doesnt, try pulling the video card. If you have on board video as well as a card, you can try it with just the on board and no video card. If not, borrow a vid card from someone. Doesnt have to be anything special, it can even be one of the old 4 MB PCI cards... just for diag. If that doesn't fix it, try pulling out any other cards that may be in it. Modem, sound, etc. etc.

and finally, here is a link to all the bios error codes for Gateway computers to help with further trouble shooting.

http://support.gateway.com/s/Servers/COMPO/MOTHERBD/WME859199/WME859199faq2.shtml

Jan 02, 2010 | Gateway GT5028 PC Desktop

1 Answer

Wont boot monitor mouse or keyboard


Ok, I'm going to need some more information here. When you turn on your pc, does the power seem to come on? Does the computer beep?

Jun 15, 2009 | PC Desktops

1 Answer

Beeps 2 times & a warbling noise when trying to boot up - unplugging power lead & pressing ON/Off button & reconnecting power lead starts up OK - but it can be OK for several days & then repeats the p


The Cause of Problem:

The Power Buttons electrical circle sometimes just braked it by one of sensors and the result is the 2 beeps and Power Supply is in protected mode error.

The whole computer is turn off but the power button is turn on and this is the nub of the matter. Because if you want turn on the computer you can't because already turn on but just the Power button and you can't do anything.

The solution:
You need just change the Power Supply and don't do anything just the power cable put into the Power Supply after turn off computer.
Finaly change back the Power Supply.

Apr 25, 2009 | HP Vectra VL420 Intel Desktop PC - Intel...

1 Answer

Using Non-Dell monitor on Dell system


Have you tried the monitor on another PC, have you checked the cables, or tried another monitor cable, AND Look inside both place the monitor plug goes and look for BENT PINS or broken PINS, not every hole may have a corresponding pin but thats OK, look for bent or broken pins, If those soutions dont work repost error code beeps, and I or someone will help more.
Thanks for the fixya rating, everyone helps me..have a blessed day

Apr 08, 2009 | PC Desktops

1 Answer

Proview 700P lcd monitor problem


Your monitor has been enabled as an extended monitor, not a clone.
Easy way to see is open a window, grab it and drag it to the other monitor (drag it right, not left). Just remember even if you have the external monitor on your left side, it is really on the right side according to the computer.
Check the display properties for a clone option if you want both to show the same thing.

Hope that helps a little.

Apr 09, 2008 | PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...