Question about Hotpoint 23 in. BFI62 Built-in Dishwasher

2 Answers

Hotpoint integrated dishwasher

Hope you can help?
When I switch on the dishwasher the third light turns green then goes out and the first light starts flashing.it makes a noise for approximately 30 seconds, then bleeps and the first light just flashes bright green. ** water seems to be entering the machine. I have checked water etc is switched on ok. Working fine up until this afternoon. Any ideas?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem cant tell how many times it blinks

Posted on Jun 16, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 185 Answers

How many times does it blink

Posted on Mar 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint BF1620 Integrated dishwasher not working


Lets try the following hope this works

1.- unplug the appliance, isolate it from the electric supply.
2.- Remove the kitchen unit plinth and check inside the inspection panels below the door to see if there is water in the base.

If there is, sponge it out and then try the machine again.

Was this helpful?

May 07, 2009 | Hotpoint 23 in. BFI62 Built-in Dishwasher

2 Answers

Dishwaher not working


switch on water appears to run in after a few minutes second and forth green lught comes on and machine stops it is a IDL500 indesit machine

Jan 09, 2009 | Indesit 24 in. IDL500 Built-In Dishwasher

1 Answer

Wash light flashes


Hi LIANNEshaun,

I'm Harvey the Master Plumber.

Your problem is: you switch on dishwasher and it seems to start then light goes onto wash and the machine stops and green light flashes

Could we have the make, model and year please?

Feel free contact me again!
Thank you,
Harvey your Master Plumber

Sep 19, 2008 | Hotpoint 18 in. DC27 Slim-Line Built-in...

1 Answer

Hotpoint dishwasher fdw60


the fault wasn't with the machine. we got new waste pipes put in and the conection for the dishwasher hose didn't have the hole for the water to release. thank you for your help

Jul 15, 2008 | Hotpoint Dishwashers

6 Answers

Green flashing lights , what does it mean ?


I have an Indesit IDL 500, the machine will start fine but after about 20 mins the Ist and 2nd button start flashing. Can you help?

Regards
Ingrid Houben

Jul 06, 2008 | Indesit 24 in. IDL500 Built-In Dishwasher

1 Answer

Still not working. Any one with any ideas how i can get it working again.thanks


Bad main control board,and fixing the board will only be a short fix.Sorry!

May 11, 2008 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Flashing green light


Hi there. It looks like water is present in the flood catching tray at the bottom which usually indicates that there is a leak somewhere. More often than not this is just a pipe with a poor fitting and simply tightening the clip is enough to stop the leak. Our machine had a very slow leak from one pipe (not enough to trigger the alarm) which was fixed in this way. The leak is detected by a small float switch located in the flood catch tray.

Undo 4 screws on the metal plate under the dishwasher 3 at the front 1 at the back, this reveals The pump check the seals are in place on the waste pump.

Mar 10, 2008 | Hotpoint 18 in. BCI45 Slim-Line Built-in...

1 Answer

Fault with Hotpoint BCI45 Dishwasher


This a generic problem with hotpoint dishwashers..
Water is present in the flood catching tray at the bottom which usually indicates that there is a leak somewhere. More often than not this is just a pipe with a poor fitting and simply tightening the clip is enough to stop the leak. Our machine had a very slow leak from one pipe (not enough to trigger the alarm) which was fixed in this way. The leak is detected by a small float switch located in the flood catch tray.

Undo 4 screws on the metal plate under the dishwasher 3 at the front 1 at the back, this reveals The pump check the seals are in place on the waste pump.

Sep 27, 2007 | Hotpoint 18 in. BCI45 Slim-Line Built-in...

Not finding what you are looking for?
Hotpoint 23 in. BFI62 Built-in Dishwasher Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

bosch5

Level 2 Expert

157 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...