We can turn tv on with remote or manuel. The tv goes off,

helllllllo.....take your glasses back off.....hahaha....[a] remove battieries from remote /put them back yes/no...[b] unplug unit & do the battery thing 2/3 minutes,,that should do it...what you did is reset......tkx........see me on amazon/ebay.....bookbundler

Hello
I thinks you may be right. All plasma and LCD panel tVs will have cooling fans at the top side. Plasma screens will heat up much more, and if cooling fans stops work, of has damaged, the set will overheat, and awill automatically shut down; because there is a overheat sensor fitted inside it, will sense the heat, and if the set overheats, it will send a signal to the main system control fo the TV; which in turn shut down the whole system. look fans for proper working. If not replace them. OK.

http://www.remotecentral.com codes for all remotes

Try taking the batteries out of the remote or taking it out of range from the tv. Then try turning the volume up on the Tv manually. If the volume continues to go down on its own then it is a problem with the tv set itself. If the problem stops with the remote out of the picture then it is a remote problem. As far as powering the unit off may be a similar issue. If there is an on/off button on the tv and it works to turn the power on but not off then it is a tv issue. If the remote turns the tv on but not off it may be something as simple as the wrong code being programmed into the remote(universal remote) or if it is the factory remote it may be an issue with that. You could try getting a new universal remote that works with your unit.

open the cover of your tv look for the sound IF using a plastic precesion screw driver adjust the IF counter clock wise slowly untill you reach a good sound or clockwise...if nothong happen solder a 0.2 ceramic capacitor to your sound IF at the coil of the IF under the board the IF has two terminals for the coil.sound if is located near the tuner section..there are two IF the video I.F and sound I.F

1. If this is a TV2 location take the remote to the location of the DVR.
2. Open the door on the right side of your receiver.
3. Press SYS INFO.
4. Press Record multiple times on your remote.
5. Exit the screen and see if the remote works, if not replace the batteries and repeat steps 1-4
6. If the remote still doesnt work, and this is a tv2 location (no receiver in the room with the tv) check the antenna on the back of your receiver, make sure that it is connected tightly and standing straight up.
7. If none of this works call Dish and ask for a new remote.

1. Press tv on your Sky remote control.

2. Press and hold down select and the red button together until the red light at the top of your Sky remote control flashes twice.

3. Press tv again

Then enter the remote control code using the number keypad. The red light will flash twice if a valid code has been entered.

Samsung Code: 0060

4. Point your Sky remote control at your TV and press the Power button. If this turns the off as you'd expect, then the tv should be set, press Select and the remote should work

5. If the TV does not turn off press tv, then press the Power button again, repeat this process until the TV turns off, when the TV turns off press Select.

If it's an Innovage brand jumbo remote, try this...
There are 2 different versions of the Innovage Jumbo remote, an old and a new.
For the old version:
1. You have to have the TV or DVD turned OFF.
2. Then, you have to push CODE SEARCH button once for 3 seconds till it lights solid
3. Then press TV (or DVD) button once till it lights once and turns solid and press the ON/OFF button very slowly and repeatedly as many as 300+ times to wait for the TV (or DVD) to go on.
4. Once it goes on...STOP and IMMEDIATELY press ENTER before you pass up the code or you'll have to start over!

This is very frustrating but my advice is to take it slow and methodical. Think the tortoise and the hare...if you go too fast, you'll redo it several times because you'll keep passing it up and accidentally turn the TV on and off suddenly and miss the code.
--------------------------------------------
For the newer version:
1. Turn the TV (or DVD) ON.
2. Press CODE SEARCH once and it blinks.
3. Press TV (or DVD) once and it blinks.
4. Press ON/OFF button only ONCE.
5. Wait as it automatically searches for the code by itself. It will have a slow long blink between each code it searches.
6. Stay alert because when the TV (or DVD) goes off, you IMMEDIATELY have to push ENTER to lock in that code before it goes onto the next one. (which it will even if the TV is off)

in our universal remote that you tried if you have thr manuel in there look for manuel code entry cheers

In order to determine whether it is the TV itself or something in the room that is causing the problem, place an object in front of the infrared eye on the TV. This is usually a transparent red plastic window on the front of the TV somewhere. Verify that it is covered by trying (and hopefully failing) to use the remote. If the TV continues to turn itself on and off, then it is the TVs internal circuitry. If the behavior stops, then it is something in the room. One of the more surprising causes for behavior like this is sunlight hitting rotating ceiling fans -- the light reflects off the fan at just the right frequency to fool the TV. I mention this so you don't limit yourself to only thinking that it must be either the TV or the remote.