Question about Washing Machines

1 Answer

Initial Power surge

Need to know the startup power surge of zanussi 1300 washer expressed in watts Machine to be installed in canal narrow boat need to know if my inverter will be able to handle the surge

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,587 Answers

Look on the back of the unit, for the average numbers for volts/amps..multiply that by 1.66(for peak power) and add a factor of 25% for power factor correction from your inverter. You may want to place a resistor/diode array in line with that, so that any reverse surge from the power cycling of the washer, won't back up your inverter feed.

Posted on Mar 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My zanussi ZWD12270G1 wont turn on


THE MOTHERBOARD MIGHT HAVE FUSED OUT , NORMALLY YOU HAVE TO TAKE THE TOP OFF AND LOOK FOR A FUSE NORMALLY A 4amp LOOKS LIKE A GLASS FUSE LET ME KNOW

Dec 29, 2013 | Zanussi ZWD1270 Front Load Washer / Dryer

1 Answer

Hi, I have a zanussi wwashing machine model= ghg1200apm. The door won't open. I plugged out the machine after the wash and when i plugged it in again, the door wont open. Can you help me?


Hi.

The door does not open because there is water inside the machine. To open the door you need to empty the tub first.

To empty the tub disconnect power, open the door at the bottom of the machine's front side, unscrew the drain filter cap and collect water using a container.

Usually that is enough to allow the door to open. If the door does not get released, try running a cycle again.

If still no luck, then the door is locked either because the pressure switch detecting water level is clogged with soap or because the power surge has damaged some component. In that case the machine must be partially disassembled to reach the back of the door opening mechanism. The door latch is reachable either from drain filter access or from top of the appliance.

Emptying water through the drain filter and/or restarting a cycle usually is enough to release the door lock.

Regards.

Ginko

Aug 19, 2011 | Zanussi ZWF12070 Front Load Washer

1 Answer

Error E20


zanussi error E20 suggests a pump/draining problem. remove pump/filter and clean it all out. its located at the end of the drain hose at the bottom of machine. power off. it might need replacement.

Nov 01, 2009 | Zanussi ZWF1430W Front Load Washer

1 Answer

Machine no power, power supply good, fuse in plug good machine will not turn on.machine type zanussi washer dryer 3 months old.


hello inside the machine theres is circuit board at the bottom there might be a glass fuse on the board which might have blown make sure the power is off before you check it good luck

shaun

Mar 18, 2009 | Zanussi WJS1265W Front Load Washer/Dryer

1 Answer

I had a power surge, new washing machine has no power


if nothing obvious fried then call warranty service, omit part about power surge!

Mar 14, 2009 | Frigidaire ATF6000ES Front Load Washer

2 Answers

ZANUSSI 1237 Washing Machine


have you tried to plug your machine in a different socket try it if you can by using an extension instead of moving the machine.

Sep 22, 2008 | Zanussi WJS1265W Front Load Washer/Dryer

1 Answer

Heating element


hi yes they are different the fc1200w element is 1600 watts (£31 part 150867200-1)the jetsystem zwf1658 1900 watts its always better to use the correct part.

May 03, 2008 | Zanussi FC1200W Front Load Washer

1 Answer

Zanussi WJD1257W Washer/Dryer


if computer is broken that is your timer dial not worth fixing sometimes as much as a new washer but it could be your interlock you can test this by closing door set machine to a programme hit the front of your washer to the right of the door as you look at it if not take lid of make sure power is off look down inside the front of your machine were your door seal is attached to the outer drum were u hit the washer on the inside will be your interlock switch replace that before paying out for a timer m8 more than likely that is the problem

Aug 13, 2007 | Zanussi WJD1257W Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...