Question about Lands Phones

1 Answer


Posted by on

  • 2 more comments 
  • hansemtravel Mar 09, 2008

    I have not seen any other error message.

  • hansemtravel Mar 09, 2008

    I hang up the phone and tried to use phone again and the heaset would not work.

    oh I remember low battery message was there too.


  • hansemtravel Mar 09, 2008

    the model no : 25414 RE3-A

    Serial no : 60005576



  • hansemtravel Mar 09, 2008

    the power is connected and still I have a message saying error : inhibited

    I have to go now I will contact again thanks for your help




1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Lands Phones Master
  • 3,614 Answers

Until when you had never use the phone?

Posted on Mar 09, 2008

  • 6 more comments 
  • micromaster
    micromaster Mar 09, 2008

    any indicator's aside from error message you see?

  • micromaster
    micromaster Mar 09, 2008

    Describe please when the error message pops-up or occur, on what kind of operation or function you are doing on the phone and give's you the error...

  • micromaster
    micromaster Mar 09, 2008

    ok.. copy that!

    can you give the model and the brand of the phone. i'll see right where you could possibly reset the phone.

  • micromaster
    micromaster Mar 09, 2008

    bullseye! OK i got it now.

    If the power cord is not plugged into the unit, and the battery is available, the unit enters Battery Operation Mode. In this mode, the

    unit fully supports all operational features, except the intercom call function.

    NOTE: Under battery operation mode, the RF module (optional for use with cordless handset) is not supported.

  • micromaster
    micromaster Mar 09, 2008

    NOTE: If the headset is not connected (or if not completely inserted into headset jack), an error tone is heard when the HEADSET button is pressed.

  • micromaster
    micromaster Mar 09, 2008

    For Restoring the Default Settings of your Phone:

    This feature allows you to reset the menu to the original factory default settings.

    1. Press the MENU button while in standby mode.

    2. Use the < REVIEW > button to scroll to RESTORE TO DEFAULTS.

    3. Press the SELECT/SAVE button.

    4. Use the < REVIEW > button to scroll to YES or NO.

    5. Press the SELECT/SAVE button to save.


  • micromaster
    micromaster Mar 09, 2008

    ok.. i'll post here many option's that you can do when your back.

  • micromaster
    micromaster Mar 09, 2008

    Take care & God Bless You..



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I reset the message indicator light?

You have unheard messages on the voicemail system provided by your telephone company. This system records messages when someone calls while you're already on the phone. Please contact your telephone company for instructions on accessing their voicemail system.

Dec 18, 2012 | GE Rca 25414re3-a Executive Series 4 Lines...

1 Answer

Missage light blinking

You have unheard messages on the voicemail system provided by your telephone company. This system records messages when people call while you're already on the phone. Please contact your telephone company for instructions on accessing their voicemail system.

Oct 29, 2012 | RCA Executive Series 25404re3-a 4 Line...

1 Answer

We have RCA executive series 4 line telephones. Is there a juction box that we can install to make this system work?

The RCA 4 line phone uses 2 standard telehpone jacks. Line
1&2 on the first jack and lines 3&4 on the second jack.

Sep 13, 2010 | RCA Lands Phones

1 Answer

The message is blinking but there is no new message. I have a rca executive series 25414re3a phone with 4 lines

I inherited this phone,; how do I check new messages when the message is blinking? I don't see anything that says play.

Jun 16, 2010 | RCA 25413RE3 4-Line Corded Phone

1 Answer

I'd like to record an on-hold message.

You'll need an aftermarket adapter that senses the voltage shift in the line, triggering a 24/7 music feed. The RCA series don't have a music-on-hold capability. is the best hardware solution, or using to put a studio package together with hardware.


Apr 26, 2010 | RCA Lands Phones

1 Answer

Have an RCA executive series. the light for the

I have an RCA Executive Line 4-line phone. I was away for a week, and came back to find the speakerphone when I dial out is significantly muffled on some of the lines (people that I am calling complain of noise on the line). If I take it off speaker, the quality on the handpiece is normal. First, I thought it was the batteries, so I replaced them. Didn't change. Is there a reset? Is the phone (base) after less than 1 year defective?

Sep 30, 2009 | RCA Lands Phones

4 Answers

RCA Executive Series 4-line model# 25413RE3-A

I was having the same caller ID. Then I looked up the phone on the RCA site:

Turns out there is no called ID on this model =(

May 08, 2009 | RCA 25413RE3 Corded Phone

1 Answer

RCA executive series

No ringer could well be a setting and light on 2nd line means their is No 2nd line and most 2 to 4 lines phones at least require 2 active lines for the system to work correctly

Mar 30, 2008 | RCA 25202RE3 Corded Phone

2 Answers

I have RCA Executive Serices 4 lin system Phone and I used to use headset all of sudden I hace message saying " Error: inhibited ". Would you plaese help fix my problem. Thanks for your...


I had the "error: inhibited" problem with my RCA 4-line Executive Series phone as well.
When I checked the line from the phone to the wall outlet, I saw that it had come undone.
After I plugged the phone back into the wall, it started working normally again.

I recommend substituting in a different, known-good telephone to see if that works.
If you can't get any phone to work plugged into that extension, then the extension is dead.
If another phone works but your RCA still will not, then the problem is with the RCA phone.

A similar idea is to try moving your RCA phone, substituting it in place of a working phone.
If it works in room X but not in room Y, suspect the phone wiring running to room Y.

This phone employs a common but awkward means of wiring up lines two and four.
Line two is wired to the wall by piggybacking on the patch cable used for line one.
Line four is wired to the wall by piggybacking on the patch cable used for line three.
A phone cord has four wires running through it, but a phone signal requires just two.
The piggybacking technique leverages the cable's free pair to feed a second line.

The upshot is that one can test the wiring for lines one and three with a simple, plain phone.
To test the wiring to lines two or four, some specialized knowledge is needed.
In place of that knowledge, a different two-line phone which also piggybacks might be used.

That's detail you'll need to consider only if your problem is specific to line 2 and/or line 4.

Anyhow, I hope I'm not patronizing by being too simple. But, I had this problem too.
It turned out to have nothing to do with the phone itself; the signal wiring to it was bad.

I realize that this feedback is a bit late and that you've likely already resolved your issue.
Perhaps this feedback will someday help somebody else (since these Q&As are archived).



Mar 09, 2008 | RCA 25403RE3 Corded Phone

2 Answers


If you are looking for a message on hold port, you will not find one. Technically speaking, this is not a phone "system." There are 2 options for using messages on hold with your phones:
1) Using a message on hold player with a built-in adapter
2) Using a message on hold player and a separate adapter

The best option can be a little tricky to determine. We work with hundreds of small businesses that have 2,3,4 line phones and can help you figure this out and deliver the best solution. Please call me.

800-832-4653 ext.240 (Drew, Sales Mgr, Commercials On Hold)

Dec 27, 2007 | RCA 25403RE3 Corded Phone

Not finding what you are looking for?
Lands Phones Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lands Phones Experts

Cindy Wells

Level 3 Expert

5589 Answers


Level 3 Expert

82331 Answers

David Burbee
David Burbee

Level 3 Expert

1871 Answers

Are you a Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides