Question about Epson LX-300 Matrix Printer

1 Answer

PITCH Changing I have LX300+ printer. Printer default pitch is 10CPI. I want to change it ti 12CPI. Please can anybody help me to change pitch. My mail - sethvintec@yahoo.com

Posted by on

  • Mark Williams
    Mark Williams May 11, 2010

    The lx300 can change cpi with software thru control panel.
    Have you tried this?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 106 Answers

You must enter in set up mode to printer,press the lf/ff buton and turn on the printer-that is the case in one type of setup firmare ,if you not enter in set up mode to try the same way with other buttons.in the set up printer print you the small guide,then you must foolw his until you reach a change pitch.

Posted on Mar 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sato cl408e - printing over perforations. I tried turning the Pitch(all the way to the right) and Offset(all the way to the left), and this helped a little, but still not right. Because of this, when the...


Reset printer sensor threshold setting.

Turn on printer whilst holding down line key untill printer beeps.

Use feed key to step to Gap in display.
Load label plus backing under sensor and not volts reading.
remove labels and place backing only under sensor and note volts reading.
use following formula
High reading + Low reading / 0.5 = Value to use
e.g 2.8 + 1.4 / 0.5 = 2.1.

use result to change value of input using line key once set press feed key to set.

To change label start position use the pitch menu.

Jun 02, 2011 | SATO CL408e Thermal Printer

1 Answer

Hello icant change settings of my button pitch and font..my printer is epson fx 2175..i had search that the problem is Font and Pitch lock mode..how to unlock it?


switch on the printer while u holding the pause button and leav it aftre 7 seconds it will print the default setting page.later on you can change it according to the paper setting.

Hope this helps. Please rate my response.
Thanks.
Have a good day

Dec 27, 2010 | Printers & Copiers

1 Answer

How to change pitch from 10cpi to 12cpi in Epson lx300+II


A complete user manual can be downloaded HERE.
Follow the instructions starting from page 2-19.

Dec 23, 2010 | Epson LX-300+ II Matrix Printer

1 Answer

LE MESSAGE 329


329 LD unit beam pitch adjusted incorrectly
The LD unit HP sensor does not detect
the ON condition while changing the LD
unit position for correcting the LD
position or changing the dpi.
• After initialization of the SP modes,
SP2-109-3 or SP2-109-4 was not
executed.
• The harness is blocking the LD drive
(PCB), preventing adjustment of the
pitch.

Lazer issue.Execute above sp modes or u need to take the lazer unit out and see if anything in the way.

Nov 21, 2010 | Ricoh Aficio 1035 Copier

1 Answer

The print image is not fully printing on the surface of disc


The pitch is a very sensitive adjustment. You need to loose one screw while tightening another to change the pitch of the head. I usually do this in 1/4 turn increments. Use the test pattern in Test mode when doing this adjustment. I have instructions if you need them..
John Norman Max Optical LLC. john@maxoptical.com 610-269-7033

May 25, 2010 | Rimage AUTOMATED PRINTERS: PrismPlus...

1 Answer

Printer epson lx-300+II


Changing the default settings in the printer using the printers panel may be a bit difficult but it should be manageable. As soon as you enter the default setting mode it will print a guide, the guide will include the current setting. The guide will also give you the corresponding value of a certain setting according to the status of the light. The first two boxes will correspond to the font lights and the last box on the guide refers to the pause light. pressing the lf/ff button cycles through the options and pressing the tear off button will select the current option and cycle through the options as well.... However, in any printing environment, the setting in the APPLICATION OVERRIDES the setting in the PRINTER. So, whatever setting you select in the printers' default will be overridden by the applications' settings....

Jun 24, 2008 | Printers & Copiers

1 Answer

Changing Pitch


use Epson remote utility to change any configuration

Mar 13, 2008 | Epson LX-300 Matrix Printer

1 Answer

Printer not Print data in English Language


Hi, you may want to reset/restore the Epson LX300 to default settings. This can be done by pressing down on the FONT button while powering on the printer. If done right the LX300 will print a test page with the firmware version. It is also possible that the drivers are corrupted. In Start, Printers & Faxes, delete the LX300 printer, restart your PC and then re-install via Add Printer. In some cases, defective parallel cable can also cause problems. Unfortunately the only sure way of checking is by replacing the printer/parallel cable with a known good/operation cable. If the printer would really be requiring service, a Service Manual is available at (http://www.eserviceinfo.com/index.php?what=search2&searchstring=DPA-300) Hope this be of some help to you. Good luck and pls post again how things turn up.

May 26, 2007 | Epson LX-300 Matrix Printer

Not finding what you are looking for?
Epson LX-300 Matrix Printer Logo

705 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Printers & Copiers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Are you an Epson Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...