Question about EliteGroup ECS 755-A2 Motherboard

1 Answer

Up grade motherboard

Monitor just keeps saying no signal

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 152 Answers

On starting windows up time press F8 and select VGA MODE
after that under windows vga properties set monitor resolution 800/600

Posted on Mar 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What should I do because it says no signal input


Sounds like your video card or monitor is bad. Most likely it's the video card because if it was the monitor the No Signal Input could not appear on the screen. To isolate the problem try connecting another monitor to the computer. Borrow a monitor from a neighbor, friend, relative or co-worker and connect it to the computer. If the Borrowed Monitor displays ok without a problem then your original monitor is bad. If the Borrowed monitor has the same issue of No Input Signal as your original monitor, then your video card inside the computer is bad.

May 30, 2012 | Biostar MCP6PB M2+ Motherboard

1 Answer

I installed 17" LCD Acer


If you have a graphics card make sure that the 'signal' cable is attached to it rather than your motherboard's built-in graphics port. other than that, make sure you have the drivers for the monitor.
e_skal87.jpg

Aug 25, 2011 | Motherboards

1 Answer

When I want to switch ma computer on after changing boxes it keeps making a noise and the monitor says no signal, the lights in front are off, but all the fans are running


You just changed the case? It seems you might've missed a videocard or motherboard power connection; fix that or simplify until it boots, then eventually reconnect the HD.

Aug 14, 2011 | Intel Motherboard

1 Answer

My monitor samsung 2330 keeps saying check digital signal cable and I've put the cords all in the same way I had them before and now this screen keeps popping up


If you already check your connections and still no answer from what you're doing, do these steps:
  1. check for any beep codes
  2. remove and reinsert your RAM to another memory slot, if it works you have a problem with your RAM, you'll need to buy a new RAM that is compatible with your motherboard
  3. if you here a 1 short beep, that means it already start the booting sequence of your computer but you don't see any boot screen and still the out of range error. You have a defective graphic card.
  4. Is your monitor is a LCD type? if your answer is yes that means your monitor is not compatible with your old graphic card, buy a new graphic card that is compatible with your motherboard and to your LCD monitor. Because old graphic cards or onboard vga cannot hold much more pixels than newer ones that's why you have an out of range error

Aug 01, 2011 | Samsung Motherboards

1 Answer

When i added a video card.. and restarted my pc. a blue screen appears... saying "overun"?? what is the problem??


well did you check weather the video card came with a VGA pin where you can connect the monitor signal cable if not , connect the monitor signal cable to the video card VGA out socket.
good luck

Jan 05, 2010 | ASUS P4S800-MX Motherboard

1 Answer

My computer is not working shows keyboard erro and stop


Hi...

When you monitor saying which is no signal this is a monitor port problem. Check your monitor connector if it is properly connceted to the motherboard. That is the only way of monitor saying no signal.

Regards
PCmania

Aug 22, 2009 | Intel PENTIUM-4 865GV CHIP MOTHER BOARD...

3 Answers

Monitor saying no signal


check the Pins in the monitors serial port and make sure all are straight 15 of em

Jun 03, 2008 | Motherboards

2 Answers

No signal to monitor when booting.


(1) Remove memory from mother board and start the system if you happen to listen long beep then RAM is not working properly.
(2) Clean RAM conducting area on mother board with clean cotton cloth, put one peice of RAM and test and check the othe peice also, if working you could any sign display . Before doing all these check mother board any LED is glowing if so your SMPS is working after you turn on UPS.

(3) Check for all proper connection for all cables. Have you connected video cable of monitor to mother board VGA (it will not work because it is disabled as soon as you installed XFX GeForce 8800 GT), your viedo output only will come through XFX GeForce 8800 GT VGA port.

(4) If propelm persits Deassmble complete the system and reassmble & do n't connect HDD, DVD, floppy. Cehck with bare mother baord, processor, RAM (put one picese at a time) by connecting viedo cable of monitor

Apr 19, 2008 | ASUS M2N-E SLI (M2N-E SLI GREEN)...

1 Answer

New power supply, but turning on no signal to monitor


well this is one of the nightmare problems I keep got into ..there can be alot of posibilities..but the most common are the video card is damdaged or the mainboard.try to change the video card and check than.if the problem persists,than is a motheboard fault..look to all the condensors,chech the intefrity of your connections..
good luck.
it is  a very booring work.

Feb 03, 2008 | E-Machines (308714) Motherboard

Not finding what you are looking for?
EliteGroup ECS 755-A2 Motherboard Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top EliteGroup Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Mark Taylor
Mark Taylor

Level 3 Expert

728 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you an EliteGroup Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...