Question about Computers & Internet

Open Question

Laserjet 2300 I have an HP laserjet 2300 that has error code 49.2342. What do I need to do?

Posted by on

5 Suggested Answers

silentspoon
  • 62 Answers

SOURCE: HP LASERJET 3700N - PRINTING PROBLEM

I'm not sure what you mean by "not printing on paper, the image area is shifting". What are you printing on?

Have you tried uninstalling the device drivers and reinstalling them? This may clear any software quirks caused by conflicting devices or user settings.

Posted on Feb 15, 2008

  • 1894 Answers

SOURCE: Fuser Error

I truly believe that you did not take the fuser out. It is not a simple process and is not readily accessible.
You most likely took out the toner cartridge, which works with the fuser.
The fuser is what "fuses" the toner to the paper so the documents print as expected. There are fuser kits that can be purchased, and they usually come with some decent instructions.


in case of new printer
A fuser problem is serious but if it is is a new printer, use the warranty now. Don't play with it as more than likely you can't recover and you *MAY VOID* the warranty in any attempts, so use the warranty. You should have returned it immediately once the problem cropped-up to be within the quicker satisfaction settlement period, you may now have to deal with a warranty center if not the vendor themselves for repair, but start the process. Plus, document this as well, cal,s letters, etc. to best serve yourself if any other problems arise.

To explain what the fuser is, one must explain what the fuser does.

A laser printer works by assembling the page in its memory, then transfers that "image" by scanning a drum. The drum then picks up a charge which will attract the toner. By varying the laser you can induce specific dots, creating an image on the drum. The drum is rotated through the toner, the charge then attracts the oppositely charged toner particles (the uncharged sections don't have anything) The drum, now dark with toner, is touched to the paper, which has an opposite charge, thus transfer all the toner over to the paper. Then the paper is sent THROUGH the fuser, which basically MELTS the toner onto the paper permanently.

If the fuser is too hot, that means the temp control unit for the printer fuser has FAILED, and that is NOT something you can fix by yourself. The labor will likely cost more than the printer unless it's under warranty.

You took out the toner cartridge, which is NOT the fuser. Toner cartridge is just the toner and the drum together in one unit. The fuser is where it warns "high temp! do not touch!"

Just buy another printer or use the backup printer. Again, this is NOT something you can fix by yourself.

Posted on Mar 17, 2008

POCBM
  • 121 Answers

SOURCE: I'M GETTING A 59.50 ERROR ON HP LASERJET P3005d. HELP

59.50 indicates a main motor failure either the motor is bad or something is stopping it from turning. can be as simple as a bad toner.
turn the machine on and listen for the motor noise if you don't hear it turn the machine off remove the toner and turn it back on if you can hear the motor running youmay just have a bad cart.
hope this helps

Posted on Mar 06, 2009

taran_2005
  • 10515 Answers

SOURCE: MY HP LASERJET 3005 DISPLAY ERROR 49.2F9D

Hi,
Its already discussed in one of the forums for Hp.
check :-
https://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1158526
Thanks

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: hp 2300 laserjet printer error code 13.20.00

this problem persist NVRAM resetting
To perform an NVRAM initialization, complete the following steps:
1 Turn off the printer.
2 Press and hold (DOWN arrow), and turn on the printer.
3 When all three status lights are lit, release (DOWN arrow) and press (UP arrow).
4 Press PAUSE/RESUME. The first item of a menu appears.
5 Use (UP arrow) or (DOWN arrow) to scroll to NVRAM INIT, and press (SELECT).

cihat ALTIN FROM TURKEY ANKARA

Posted on Nov 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My HP Laserjet 1012 is printing at a slight right upward angle. any ideas? is there an alignment procedure i can perform?


Yes , this is an alignment problem

This sounds as the the paper is not being guided properly by the guide roller or transfer guides. May need cleaning or replacement is needed. \

Mar 23, 2010 | Computers & Internet

1 Answer

HP Laserjet 4600 help


Apparently it was a defective black ink cartidge.  Thanks anyway.

Mar 27, 2008 | Computers & Internet

1 Answer

Garbled prints on HP LaserJet 2100


Try re-installing latest drivers from HP website.

Mar 27, 2008 | Computers & Internet

1 Answer

Driver required for HP laserjet 1018 with Applemac OS 10.4.10


Unfortunately, the 1018 is not supported in the mac environment.
Unless you are familiar with changing the source codes from linux to MAC I wouldn't attempt it.

The other option would be to set the printer up on a different machine as default and using a program like NETWORK MAGIC,
network the computers together and share the printer, Use the trial version first to see if it works.

Mar 19, 2008 | Computers & Internet

1 Answer

HP 8150N ERROR CODE 79.060E


Power off the printer. Unplug the printer's USB cable for 5 seconds replug turn on the printer. If that fails power off the PC and printer unplug the USB cable at the PC and printer replug and power back on the PC. After PC is fully booted turn the printer back on. If this keeps reoccurring please replace the USB cable and or try different USB ports.

Mar 18, 2008 | Computers & Internet

1 Answer

Fuser Error


I truly believe that you did not take the fuser out. It is not a simple process and is not readily accessible.
You most likely took out the toner cartridge, which works with the fuser.
The fuser is what "fuses" the toner to the paper so the documents print as expected. There are fuser kits that can be purchased, and they usually come with some decent instructions.


in case of new printer
A fuser problem is serious but if it is is a new printer, use the warranty now. Don't play with it as more than likely you can't recover and you *MAY VOID* the warranty in any attempts, so use the warranty. You should have returned it immediately once the problem cropped-up to be within the quicker satisfaction settlement period, you may now have to deal with a warranty center if not the vendor themselves for repair, but start the process. Plus, document this as well, cal,s letters, etc. to best serve yourself if any other problems arise.

To explain what the fuser is, one must explain what the fuser does.

A laser printer works by assembling the page in its memory, then transfers that "image" by scanning a drum. The drum then picks up a charge which will attract the toner. By varying the laser you can induce specific dots, creating an image on the drum. The drum is rotated through the toner, the charge then attracts the oppositely charged toner particles (the uncharged sections don't have anything) The drum, now dark with toner, is touched to the paper, which has an opposite charge, thus transfer all the toner over to the paper. Then the paper is sent THROUGH the fuser, which basically MELTS the toner onto the paper permanently.

If the fuser is too hot, that means the temp control unit for the printer fuser has FAILED, and that is NOT something you can fix by yourself. The labor will likely cost more than the printer unless it's under warranty.

You took out the toner cartridge, which is NOT the fuser. Toner cartridge is just the toner and the drum together in one unit. The fuser is where it warns "high temp! do not touch!"

Just buy another printer or use the backup printer. Again, this is NOT something you can fix by yourself.

Mar 17, 2008 | Computers & Internet

1 Answer

Eratic printing of colour pages


probably needs an alignment test as well as a colour check.

Failing that try using a new ink cartridge.

Hope this helps

Feb 14, 2008 | Computers & Internet

1 Answer

HP LASERJET 3700N - PRINTING PROBLEM


I'm not sure what you mean by "not printing on paper, the image area is shifting". What are you printing on?

Have you tried uninstalling the device drivers and reinstalling them? This may clear any software quirks caused by conflicting devices or user settings.

Feb 08, 2008 | Computers & Internet

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

100340 Answers

David Payne
David Payne

Level 3 Expert

14160 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...