Question about HP Officejet 4315v All-In-One InkJet Printer

2 Answers

STUCK IN ALIGN PAGE MODE

I cannot get my printer out of the align page mode to do a print job. the last operation i did was a copy operation, and since then i can't get it to print off the computer. have turn everything off and on several time and removed and reinserted electric cords. nothing works.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

YOU ROCK THANKS A MILLION TIMES been dying to fix this IT WORKS THANKS THANKS THANKS

Posted on Jul 01, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 79 Answers

Hi,

Perform a semi-full reset on the all-in-one by following the steps below
1
Take out the cartridges from the unit .
2
Make sure the unit is connected to the wall jack directly without any surge protector.
3
Unplug the power cord from the back of the unit ( without turning off the unit ) .
4
Now press the # and 6 key together , while holding these keys down plug in the power cord back into the unit .
5
Do not release the keys after a few seconds u will find te hp logo or bars moving across the screen .wait while the unit turns off.
6
after one minute turn on the prnter . it will go into alligment phase > let it finish .

7 Allow the all-in-one to re-initialize. This may take a minute or two.

8 If prompts appear in the all-in-one display to set the front panel language and country settings, perform the steps to set this information

Thanks

Posted on Jun 06, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cannon D680 prints a blank page after every print or copy job. the pages print fine but at the end it always feeds 1 blank page. what can it be?


See if there is an option in your settings to print a "job owner" page after each job. That's not what it's actually called but I had a similar issue with a Canon printer and found that you can have the printer automatically print a page after the job that identifies who sent the job to the printer. It's the last page so it lands on top of a finished job and separates it from other jobs sent to the printer before you have a chance to get yours. If you don't have network identifications associated with users it may just print a blank page as a separator.

Jan 14, 2015 | Canon imageCLASS D680 Laser Printer

1 Answer

The Lexmark x5495 printer is not printing correctly. The printout is not aligned properly. The printout is crooked. How can you solve this problem?


Try to re-seat your cartridges and make sure they are properly inserted in the cartridge carrier.
If that doesn't help, please do the Align Cartridges function on your printer. From the printer operator panel, while on Copy mode, press the Menu button > Tools > Maintenance > Align Cartridges. You printer will then print a test page that will help align the cartridges.
After the page is printed, try to print a document again to verify that the problem is fixed. Thanks.

Feb 25, 2012 | Lexmark X5495 Printer

1 Answer

How to cancel print alignment page


To cancel any print jobs, or the copy and scan function, simply press the Cancel (red X) button on the printer operator panel.
I hope this information has been helpful.

Nov 11, 2011 | Lexmark X2670 All-In-One Printer

1 Answer

X4270 won't copy after replacing black cartridge. It did run an alignment page, however.


Try this approach:
  1. On the printer operator panel, on Copy mode, press Options.
  2. Select Maintenance.
  3. Select Clean Cartridges
Your printer will then print a test page forcing ink through the cartridge nozzles and clean them.
Try to print your document again to verify that Copying is properly functioning now.

Aug 08, 2011 | Lexmark X4270 All-In-One InkJet Printer

1 Answer

I can't print an alignment page from my computer. How do I align my computer?


Alignng your Lexmark:
1. Load paper in the paper tray.
  1. On the control panel, press Mode repeatedly until Copy is selected.
  2. Press Options until MAINTENANCE appears.
  3. Press + until Align appears, and then press Select.

An alignment page prints. Once this page prints, your automatic alignment is complete.


This works on Lexmark Printers, if it doesn't let us know what model you have.


If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

May 20, 2011 | Lexmark All-in-One Printer with PictBridge

1 Answer

The printer prints an allignment sheet every time its turned on.


Bypassing the print cartridge alignment It is possible to bypass the alignment page and use the information from the last successful alignment. Print quality may not be as good, but the product will operate. The table below describes how to bypass the cartridge alignment. Try either one of these: Press and hold the Enter button, and then press Setup or Press and hold the Setup button, and then press Options (or Copy Options ).

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Feb 11, 2011 | HP PSC 1350 All-In-One Thermal Printer

1 Answer

HP 7210 Officejt is not printing


Hi,

Are you able to make copy from printer or print test page ?
If you are not able to make copy from printer or print self test page
Check if the cartridges are not empty.
If they have ink, follow the steps below

1. Disconnect the power cable from back of printer
2. While holding the # and 6 button, connect the power cord to printer.
3. It will print the alignment sheet and you will have to re-align the printer and try to print/copy
*Note this is Semifull reset and doing so you may loose fax logs and other fax related setting you have setup on printer.


Or are you not able to print from PC ?

Click the link below to know how to resolve the print job stuck in queue issue.
Link

Oct 23, 2010 | HP Officejet 7210 All-In-One InkJet...

1 Answer

I cannot get the printer to copy anything, it just goes into the align mode. It will print things from my computer.


Hello,

Start up your multi-function printer and computer. Wait until it has powered on completely before beginning.

Open the printer's lid and place your item on the copying surface with the side you want copied face-down on the glass. Double-check the alignment.

Shut the printer's lid. For large items, such as books, you may want to remove the printer lid rather than forcing it closed.

Choose the kind of copy you want: black-and-white or color. You also may have to select the kind of paper that you are copying.

Size the copy to the page if desired. Some multi-function printers allow you to expand or shrink the original to fit different sizes of paper.

.Enter the number of copies you want. You may do this on the multi-function printer or in the print setup of your computer. Make sure the paper tray has enough paper to finish your copying job.

Press the "Start" button. Other names for this might be the "Copy" or "Print" button.
Remove the pages as they are delivered from the printer's feeding mechanism.

Do not tug on the copies as they come out. Let them fall into your hands.

Take care.






May 15, 2010 | Office Equipment & Supplies

2 Answers

Keeps wanting to print alignment page


To align the cartridge from the control panel:
Please follow the steps given below:

1. Please Load a plain paper.
2. Press and hold the "Scan" button for three seconds.
3. An alignment page prints.
4. Place the alignment page onto the scanner glass.
5. Press the "Scan" button.
6. Once scanning is complete, the cartridge has been aligned for optimal print quality. Alignment must be complete before continuing with any print jobs.

Apr 20, 2009 | Lexmark X2470 All-In-One InkJet Printer

1 Answer

Can't print a complete print job without problems


There may just be some type of configuration issue going on if you don't have a drive installed in this printer. If there is no drive installed the printer drivers may be functioning as if there's one present which results in this error. I'm providing you with a few possible solutions as it is more difficult to pinpoint an issue when you don't have access to the device.

If it is a configuration issue you can try these steps:

1. Mopier mode should be disabled.
Right-click printer then click properties.
You should find a device settings tab...scroll down to mopier
mode and make sure it's disabled.

2. Printer Hard Disk should be disabled.
Right-click printer then click properties.
Go to the Device Settings tab...scroll down to Printer Hard Disk
and make sure it's disabled.

3. If you had to disable one or both features then the very last thing that you want to do is try printing a multiple page document to see if this worked.

If you check these two settings and find that both the mopier mode and printer hard disk are disabled then you can try this:

Click this sentence to follow the link to HP's driver and software page for the 4600 series printers. Find your operating system in the list and click on it. This will bring you to the page with drivers, firmware, and additional software provided for your printer type. Try downloading the drivers (unless you have the installation CD) and reinstalling the printer. Also, make sure that you have the latest Service Pack installed for your operating system. If you're using Windows XP then the latest Service Pack is 3.

Hope this helps. I work with HP printers and sometimes I have to try more than one solution before I find the right fix.

Please share your experience by rating this solution and thanks for using Fixya.

Mar 17, 2009 | HP LaserJet 4600dn Color Printer

Not finding what you are looking for?
HP Officejet 4315v All-In-One InkJet Printer Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...