Question about Vizio P4 46 in. HD-Ready Plasma Television

1 Answer

Tv turned off and wont turn on

Ok. The TV after 1.5 yrs just turned off, and wont trun on again. Instead i get a flashing light by the power button 2x repeatedly.

Posted by on

  • 1 more comment 
  • geo1671 Jun 14, 2008

    I got the same problem--2nd boat anchor. Hope someone can lead us to a factory repair manual. Anyone know how to retrieve it at--

    http://nationalservicealliance.com/visio...

    Note; above is not the p4 text but example what is offered at national

    Please let George know or copy me

    gada.2004@3web.net

  • reedwhit Sep 02, 2008

    I have a Vizio P4 46 inch plasma PDP and it will not power on. The green light comes on like it is on but there is no light at all on the tv screen. I pulled the back off of it and checked the on board fuses and they look okay from what I can tell. I also looked on the front face of all the boards that feed from the power supply and again nothing burned looking. Anyone have hints? Or should it go in the trash?
    -R


  • Anonymous Mar 13, 2014

    Wont charge the light don't trun on nothing happens

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

If there is no picture and not even a hint of backlighting, it sounds like the plasma panel itself may have gone bad.

Posted on Oct 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sony bravia kdl-32bx300 wont turn on


https://community.sony.com/t5/Television-General/Red-light-blinks-6-times-tv-won-t-come-on/td-p/47107

Mar 14, 2016 | Flat Panel Televisions

1 Answer

Can set up th remote control for this tv with the direct tv cable remote


Here's how to scan for TV codes on your DIRECTV remote

1.Make sure your TV is turned on.

2.Slide the mode switch at top of remote to "TV".

3.Press and hold the MUTE button. This is located above the number 1 button.

4.While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.

5.Then enter 991, the green light on remote should flash twice.

5b. Press 1 again (it will flash twice again), then you press the power on button at the very top right.

6.Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.

*If you hit channel up very fast, you risk going past the code. Pressing channel down will back it up. I alway hit channel up very fast till the tv turns off, then back it up slowly till it comes back on.

7.When the TV powers off, press and release the SELECT button.

*Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.

Mar 05, 2011 | Curtis LCD2425A TV

1 Answer

MY Sharp LC46D62U wont turn on


Power and OPC LED lights flashes?Common on Sharp LCD tv.Tv is still useable.Tv have Tuner signal board problems.Every times Power and OPC LED lights flashes.Just push the remote power button again and wait.Sometimes Power and OPC LED light will flashes require push power again wait again Power and OPC will flashes two or three time push power button and wait.Must do this two or three time before the backlight will light up and tv work.

Jan 07, 2011 | Sharp Aquos LC-46D62U 46 in. LCD HDTV

1 Answer

Tv wont turn on used it for two months and one day it turns on then the power led light flashes and the opc led light ...


This tv still under warrenty?Yes take ur warrenty repair.This problems very common on Sharp LCD tvs.I have one too.This tv have a Tuner signal board problems.But this tv still use able.Just push power button again after the POWER and OPC flashes.POWER and OPC some will flashes again and wait just push the power button again and wait.Sometimes have to push power buttons and wait power button push out of three or four times power button push POWER and OPC flashes.Than tv will work again.

Jan 06, 2011 | Sharp LC-52D64U 52 in. LCD HDTV

1 Answer

TV wont trun on. Pull plug and wait 5min, still wont turn on. What can be done to fix this


Tv turn on?Front LCD panel LED power light indication flashing?Yes,than the power supply board is dead,that the board where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

Jul 09, 2010 | Philips 32PFL3403D/27 32 in. LCD TV

1 Answer

When I turn on the TV the blue indicator light comes on but there is no display, then the blue light starts blinking.


The following steps should be able to correct the problem:
1) Unplug the TV or remove AC power from the TV
2) Count to ten and then plug in the TV
3) Locate the [Menu], [VOL-] and [Power] button on the TV’s side panel
4) Using the buttons on the TV’s Side Panel, press and hold both the [Menu] and [VOL-] buttons.
5) While holding those buttons, press and release the [Power] button one time and count to 3 before releasing the [Menu] and [VOL-] buttons.
6) The TV’s lower left Blue Power LED will come ON.
7) Wait 30 seconds. Confirm that the blue LED on the Lower Left of the TV (not the iPod dock for iPod models) has remained ON during this time.
8) Press the [Mute] button on the TV remote twice
9) Unplug the TV or remove AC power
10) Count to ten and plug the TV in
11) The TV power should automatically come ON and the blue power LED with be ON
12) Wait 40 seconds and the TV picture should appear
13) You can now continue using your TV.
14) If the picture does not appear, power on the TV manually:
· If the LED begins flashing, unplug and power ON a second time.
· If the LED begins flashing again, power ON the TV without unplugging
If the LED begins flashing again, contact us directly by phone to obtain a local authorized service center for you.
If the TV does power on, please reply back with the software version number for us to research this issue. Please follow these steps to obtain the software version number:

1) Press the [Menu] button on the remote control.
2) Using the arrow keys in the center of the remote, scroll over to the "settings" menu and select the [OK] button on the remote
3) Scroll down to "system info" and select [OK] button on the remote

Dec 19, 2009 | JVC Flat Panel Televisions

2 Answers

My samsung tv wont turn on, red light keeps flashing on the front.


i had this with my samsung and my mums instead of pressing red power button press either switch from analog tv to digital button or just press a number

Jun 04, 2008 | Samsung LE32R74BDX 32 in. HD-Ready LCD...

Not finding what you are looking for?
Vizio P4 46 in. HD-Ready Plasma Television Logo

354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vizio Flat Panel Televisions Experts

The Knight
The Knight

Level 3 Expert

68352 Answers

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Vizio Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...