Question about Lexmark E232 Laser Printer

2 Answers

Lexmark E232 Printer prints all characters fine but leaves about an inch gray/black margin on the left side of the paper. Tried replacing the toner cartridge and it didn't help. Any suggestions?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers

If this model has separate toner and photoconductor then the photoconductor is at end of life and needs to be replaced. Follow the directions that come in the new photoconductor package to install and reset the PC count this is important.

Luck

Posted on Mar 11, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,587 Answers

Did you try a test page to see if it's that way too?

Posted on Mar 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Printer prints off the side of the page


Hp2600n Colour Printer Colou Problms

Feb 14, 2014 | Lexmark E332n Laser Printer

1 Answer

Blotches on the left margin


Inspect the overall paper path for signs of spilled toner.Gently clean the contaminated areaswith a soft cloth or compressed air. Also try cleaning the printhead. Click on the link below and follow the instructions.
http://bitly.com/oMzZIl
For further assistance please contact Lexmark Technical Support Center.

Feb 03, 2011 | Lexmark E232 Laser Printer

1 Answer

Our HP 4250N Laser Printer is leaving a black line approx 2 inches off left side of paper. Tried cleaning rollers and putting printer into clean mode. Nothing is working. Any advice? Thank you.


This is caused either by the fuser or the tonercartridge.

The most common cause is the tonercartridge.
You can test this by forcing a paperjam to stop the paper just after the toner but before the fuser.

To force a paper jam print you can print a page from the manual feed tray and as the last third of the page enters the printer opening the door causes it to halt.

If the black line is there before the toner is bonded to the paper by the fuser you should replace the tonercartridge..

Jan 04, 2011 | HP LaserJet 4250n Printer

1 Answer

HP 2840 will not print on 3 inches of left side of page


Take the toner cartridge out, shake it back and forth, and turn it around in a circle a few time. Put it back in the priter, and print. Order a new toner cartridge.

If this is an inkjet printer, ignore this response.

Apr 21, 2010 | HP LaserJet 2840 All-In-One Printer

1 Answer

Lexmark laser printer leaving a white streak 2-3


take a q-tip and clean the scanner window. this is located in a 3/16' opening on the roof of the printer cavity it will be about 8inchs long. pull the toner cartridge and feel with your fingers on the roof of the cavity this will be located above the transfer roller slightly towards the front of the printer. white lines like this mean the laser is being blocked usually by a bit of toner or other dirt of some kind

Nov 30, 2009 | Lexmark E232 Laser Printer

1 Answer

Printer making marks down the left hand side of every page


hello,

This sounds like the photoconductor units for both black and blue need to e replaced. Open the front of the printer like you are changing toner cartridges. On the front door parts that opens to you there will e four pieces, 1 for each color. Look at the one with blue on it and the one with black and look on the ends of these, they are the photoconductor units. I bet both of the colors have worn sections compared tothe magenta and yellow ones. The replacement part number is C53030X and you will need 2 of these. They have a life span just like toner and have to be replaced too.

I hope this helps,

Buddy
Corporate Computer
Over 21 years of PC and printer support/repair

Jun 18, 2009 | Lexmark E232 Laser Printer

2 Answers

Lexmark E232 - BLACK SMUDGING on sides of print


try replacing the toner cart. or toner leaked on the area below in which case you will need to blow it out.

Jun 04, 2009 | Lexmark E232 Laser Printer

1 Answer

HP LaserJet 2430 prints vertical grey bands


It is a bad Toner Cartridge or Fuser. Most likey a bad toner cart.

Mar 07, 2009 | HP LaserJet 2430n Printer

1 Answer

Printing missing column


This could be several things-here is a list in order of probability... 1. transfer roller dirty, especially if inside of printer looks like it needs a cleaning. You could vacuum with toner vacuum or take it in for service. 2. scanner mirrors dirty. would need to be serviced by a technician. 3. scanner toner shield out of position-tech needed. 4. toner cartridge (even though its new) needs to be shaken horizontally-toner could be all on one side of hopper. Thanks and good luck...

May 15, 2007 | Lexmark E232 Laser Printer

Not finding what you are looking for?
Lexmark E232 Laser Printer Logo

947 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Printers & Copiers Experts

Roopesh S
Roopesh S

Level 2 Expert

228 Answers

Sanath Kumar V

Level 3 Expert

684 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Are you a Lexmark Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...