Question about Minolta 2430DL Color Laser Printer

1 Answer

Minolta 2430DL ColorLaser

Hello,
I'm a tech for the some of the boys and girls clubs of norhttowns in and around buffalo, ny. I have a couple of 2430dl printer in some of the clubs. My problem is i order a drum unit for 1 of my clubs and installed it just fine. But that printer completely broke within a couple of days. so i took the drum unit out of there and installed it into another 2430dl that had a low drum unit displayed on it. when i replaced it with the one from the other printer that broke, i still get the "low drum unit" on the display. do i have to reset something? this drum unit only was used for about 10 copies of paper before this printer broke. can you email me at cbrown@bgcnt.net with the solution?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 170 Answers

There is only a manual reset for the toners but I'm sure you already knew that... The drum is just a plug-n-play type consumable and should just reset automatically unless it's an old drum... ( make sure that you didnt make the mistake like so many of us a reput the old drum back in again) if your sure its the new one then it's obviously defective and depending on where you got it you should be able to defect it out for credit... hope this helps... www.bigmoneycentral.com

Posted on May 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, A Minolta bizhub cf3102 was donated to our Boys & Girls Club recently. When we first hooked it up it worked fine and then we turned a few days later it read "malfunction detected" and...


For now you should be able to turn off the MAIN power and then turn it back on to reset the code. Sometimes you may have to do this a couple of times. To resolve this permanently you will need a Minolta trained tech to come out and perform a modification to you PWB-C circuit board. It needs a capacitor replaced. Fairly simple operation but a common code I have seen many times and thus Minolta has a technical publication on it with the modifications needed. For now tho just cycle the power until it comes up to ready and then it will run fine. It is only a cold start issue and is worse if the machine is in a cool office environment.
Good Luck and Thank You for using Fixya.

Nov 18, 2010 | Minolta Printers & Copiers

1 Answer

I have fetal error code 08H,14H &15H in KONICA MINOLTA Magicolor 2430DL. pl help to resolve the problem


 When fatal error codes are displayed call tech support at Konica Minolta:
http://kmbs.konicaminolta.us/content/salesservicelocator/findservice/findservice.html

 
FATAL ERRORCODE:XX
An error has been detected with the item indicated "XX" in the service message.
Reboot the printer. This often clears the service message, and printer operation can resume.
If the problem persists, contact Technical Support

Jul 14, 2010 | Konica Minolta magicolor 2430 DL Laser...

1 Answer

Is there a Windows7 printerdriver available for the Minolta 2430DL


Usually the Vista printer drivers will work in Windows 7 as well.

Nov 15, 2009 | Minolta 2430DL Color Laser Printer

2 Answers

Minolta Magicolor 2430dl Color smudges line on edge of paper


please check the transfer belt, it seems that the transfer belt is not cleaning very well, if you find same marks on TBU then you may try to clean the cleaning unit if no help, then replace TBP.

Aug 12, 2008 | Konica Minolta magicolor 2430 DL Laser...

1 Answer

Minolta 2430dl has no display


check display wires connected to pwb

Jul 25, 2008 | Minolta 2430DL Color Laser Printer

1 Answer

Konica Minolta magicolor 2430DL


Open the top cover. Remove the drum (part with long green handle). Below the drum you will see a strip of glass about 4-5 inches long. Take a cloth and wipe across the glass.

This will normally clear up any white lines in your print.

Jul 11, 2008 | Konica Minolta magicolor 2430 DL Laser...

2 Answers

Minolta 2430DL Jams on the first Page of the Job and then Works Fine....


They are the stripper fingers and can sometimes pop out of position because of build up, you may want to try to clean these and check this specific finger against the other ones to make sure it is seated exactly like the others are...they are spring loaded so be careful when you back them away from the heatroll to clean them, they can be a real joy to put back in without the proper tools...

May 11, 2008 | Minolta 2430DL Color Laser Printer

Not finding what you are looking for?
Minolta 2430DL Color Laser Printer Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Minolta Printers & Copiers Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

5695 Answers

CheckitRight
CheckitRight

Level 3 Expert

1349 Answers

David Burkhart
David Burkhart

Level 2 Expert

207 Answers

Are you a Minolta Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...