Question about Bosch Classixx WFC 2465 Front Load Washer

1 Answer

Brushes change brushes in classixx 1200

Posted by on

  • clonman Mar 10, 2008

    ok i changed the brushes,simple put the machine on it's side,take off the motor, (2 bolts). there are two little metal notches holding in the brush.bend them back to allow the brush to come out.
    the brush is a little fiddly to put in as there is a spring involved,but only needs a little patience. ps this machine has done an average of nine washes per week for five years and nine months

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 351 Answers

Most brushs are screwed to the back of the motor which are very easy to replace,other are inside the motor and you have to dismanttle the motor.i hope this is what you wanted to know.your question wasnt clear.

Posted on Mar 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace brushes on a classic 6 1200


Disconnect the power
disconnect hoses
lay machine on it's left side
remove back cover screw and cover
slip belt off pully
unplug motor wires
undo bolts holding motor
pull motor to rear of machine
revome motor to bench
locate brush housings
undo retaining clip and slide out old brush
fit new brush
replete with other brush
reasonable in reverse of removal

Oct 04, 2014 | Bosch Washing Machines

1 Answer

F21 flashing on my bosch classixx 6 1200 express


F21 is a motor fault and in some cases can also involve a module fault. It could be as simple as the brushes need replacing or the drum has been severely out of balance.

Mar 21, 2013 | Bosch Washing Machines

1 Answer

F21 has appeared on my Bosch classixx 6 1200 model


F21 normally indicates a fault with the motor or the main control board. It could be the motor brushes need changing.
If you've changed the brushes you now need to erase the stored errors and try the machine again.
.
Turn the knob to off.
Close the door.
Turn the knob to 6 o'clock position.
Wait 2 seconds.
The start/pause should begin flashing.
Press and hold the spin button. (the spin button is the one that changes the spin speed, it may be marked "RPM")
Turn the knob to 7 o'clock position.
Wait 2 seconds.
Release the button.
Turn the knob to off.
.
This should erase the error code and get you running again.
.
If the error code returns, you have a problem with the motor, wiring or main control.
If the machine won't go into diagnostics to erase the error code, it would suggest a faulty control board.
.
Try it several times to see if you get it reset.
.
Note, If the start button doesn't flash, just carry on trying to erase the codes.

Dec 22, 2012 | Bosch Classixx WFL 2066 Front Load Washer

2 Answers

Where are the carbon brushes on a bosch classixx 1200 express


Generally speaking, you might only expect to find carbon brushes in the motors used in some power tools. Household appliances use a different type of electric motor that does not use carbon brushes.

Aug 03, 2010 | Bosch Washing Machines

1 Answer

Flash from the back of the washing machine.


it sounds like the brushes have gone in the motor that turns the drum

Apr 21, 2009 | Bosch Classixx WFL 2066 Front Load Washer

1 Answer

Bosch classixx 1200 fills, drains, but won't wash ?


This a classic example of worn brushes in the motor.
To check , remove rear panel, remove drive belt.
Unplug motor lead, undo 2 screws that secure motor, and lever motor back with a screwdriver or similar.
Keep hold of the motor as you lever it back.
You will find the brushes at the terminal end of the motor, replace if less than 4=5 mm in length.
Refit motor belt and motor plug.Test. before you refit panel
Plz rate my solution.
Thanks.

Jan 12, 2009 | Bosch Washing Machines

1 Answer

Bosch Classixx 1200 Express wont spin!!!! HELP


Make sure that all the water has drained from the washer, if it has a filter, remove and clean, it is located behind a removable plastic panel at the front of the m/c, if it still does not spin, suggest you remove motor and check the brushes for wear, this is often the reason it won't spin, but will wash o/k.
Plz rate my solution.
Thanks

Dec 22, 2008 | Bosch Classixx WFC 2465 Front Load Washer

2 Answers

Changing the brushes when the motor is off


Remove belt, unscrew 2 bolts that hold the motor, unplug the motor connector, lever the motor back with a screwdriver. Check the motor brushes, if they are any shorter than 1 cm replace brushes.

Nov 16, 2008 | Bosch Classixx WFC 2465 Front Load Washer

2 Answers

Bosch classixx 1200 express


Not a programme error but carbon brushes on motor.Fixed by local engineer.

Aug 30, 2008 | Bosch Classixx WFC 2465 Front Load Washer

1 Answer

Brushes


I just did this and had to take the motor off because I couldn't get to one of the brushes. It was easy to get off (only 2 bolts) and just as easy to put back on. Taking the motor off made life much easier as fitting the brushes is fiddly.

Jun 03, 2008 | Bosch Classixx WFC 2465 Front Load Washer

Not finding what you are looking for?
Bosch Classixx WFC 2465 Front Load Washer Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...