My oven will not stay on .F9 code appear whats the problem?

bad control board

How To Fix Oven With Little or No Heat When Baking ...

www.partselect.com/Repair/Range-Stove-Oven/No-Heat-When-Baking/

Repairing a range, oven, or stove can seem like a big task, but our ... Most electric ovens use both the bake element and the broil element in a bake cycle, with the bake... If the bake element isn't working, the oven may not reach the set temperature or ...If the element appears to look normal, then turn the oven on to a bake ...

Electric Stove Repair ' Electric Oven Repair Manual ...

www.appliancerepair.net/oven-repair-4.html

Inside the oven, the heating element is called a "bake" or "broil" element. ... To maintain a set temperature in an electric cooktop, the element is cycled on ... Do not put any cleaning agents or solvents directly on heater elements or surface units. ... A switch will show no continuity when off and good continuity when turned on.

Electric Oven Will Not Heat ' RemoveandReplace.com

removeandreplace.com/2015/.../oven-not-heating-how-to-fix-range-repa...

Aug 24, 2015 - The issue is most likely a bad internal fuse, oven temp sensor, ... oven replacement parts ... Bake and Broil Element Test - Electric Oven Repair ... Dryer Spins But No Heat - How To Troubleshoot Dryer is turning the drum but ... If your dishwasher is completing the wash cycle but will not dry your dishes, we ...

Oven Temperature Not Accurate - Repair Parts ...

Sounds like you have it figured, need to spend some moola..........

You can ohm out the sensor to the oven should be about 1100 ohms at room temperature.((the sensor is the little rod with two wires attached to it sticking in the oven, as temps change resistance changes which is read by the board) The upper and lower oven sensors are probably the same,you could just swap them to test, but probably not necessary,might also be confusing if you do not do a lot of testing on a regular basis. Remember to unplug unit for safety.

The bake element if it was not bad should be about 20 ohms, bad would read open........

Unplug the range open the control panel to access the electronic oven control. Unplug the wires and wait 5 minutes. Replace all wires on the control and turn the power back on.
If this does not reset your oven control it must be replaced.
Your ERC(clock) is bad and must be replaced.

The "F2 - E0" error code means "Shorted keypad".

Remove power from the range, open the control panel and unplug the membrane switch ribbon from the control board.Reconnect power to the range and observe for an hour.If the error code reappear - replace the control board.If not - replace the membrane switch.

1. After self cleaning the range the door won't open
   
2. Ceran glass cooktop and how to keep it clean
   
3. Changing a basic bake element
   
4. Checking a range element
   
5. Checking a surface switch
   
6. Checking the terminal block of a range element
   
7. Checking an common oven temp sensor
   
8. Checking an oven temp sensor: What does an oven temp sensor look like ??
   
9. How to adjust a standard controlled oven temperature
   
10. How to adjust the oven temp on some common electronic controlled ovens
    
11. Help for storing an appliance
    
12. How to test many brands of Ranges that are flashing a F1 fault code
    
13. Important disclaimer
    
14. My electric oven will not heat
    
15. My Range is flashing an " F1 F2 F3 F4 F5 F7 F9 " something, what does this mean??
    
16. My surface element stays red all the time, it seems to have no low heat
    
17. My whole range is totally dead...help!
    
18. My bake element just caught fire...help!!
    
19. Oven door and door hinge help
    
20. Oven temperature seems to be incorrect
    
21. Oven temp sensor - how to change helps
    
22. Replacing an old style bake/broil relay
    
23. Some "how to set the self clean" on my range
    
24. Stainless Steel Cleaning
    
25. Wiring help for the 4 prone receptacle
    
26. Wiring a replacement surface element switch WB21X5243
    

oven door will not close tight - what is wrong

F9 code usually means that the temp sensor in your oven is at fault . The electronic oven control is sensing a fault with that part. that part is pretty simple to replace Call a local service company with model and serial # they should be able to get the part for you ! Temp sensors are usualy located inside the oven in the upper left hand corner 2 screws hold it in place .It pulls out and has a conector on the back that unplugs.

Question: does the unit appear to hold the correct temperature? Most convection units only turn the heating elements on and off...not the fan. If the unit is reporting operating temp and then taking other direction...and it is cooking right...you're done.

I hit the same F9 problem when trying to self-clean, except that the door was locked OPEN.

After much trial and error, I found the following fix: 1. Switch circuit breaker off. 2. Switch circuit breaker on. 3. Press Bake button. 4 Press the small/inside button which indicates that the oven door is closed.

The lock mechanism opened and the oven now works fine.