Question about Toshiba 50H72 50" Rear Projection Television

1 Answer

How do you replace the ICs (stk392-110)

I am trying to take care of this myself. Before the warranty expired 2 years ago the BEST BUY repairman replaced 2 ICs. I am hoping that's all I have to do since I have the same problem again. I ordered the parts but I have never worked on a tv myself before.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Nina,
What is the tv doing or not doing? What parts did you order?
r.

Posted on Mar 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was told by a repairman that my convergence module is bad on my ws 55511 or best buy model ws b55 was wondering what a convergence module cost. my power went off and when it came on the red images were...


Any shop with experience should be able to replace the convergence ICs which are the likely problem. This type of repair will cost less than the boaqrd replacment and won't require a conmplete reconvergence adjustment. The parts cost around $25-$40 each (there are 2).

I would look for someone that is able to change the ICs rather than the entire board.

Dan

Jun 22, 2010 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

Samsung HC-P4752W Does Not Turn ON


The proble you have is an intermittant power supply or sweep power supply. Unless you can find a bad connection on the power and deflection board, this could be a very difficult problem to find. I have ran across this problem a couple of times, and after spending countless hours troubleshooting, I replaced the main board and all the problems were taken care of. The board part number is at samsungparts.com and I found the board for you. it is located here: http://www.samsungparts.com/part_detail.asp?catalog%5Fname=Parts+and+Accessories&product%5Fid=BP94%2D01266A&search%5Fmodel=HCP4752W Good Luck

Jul 04, 2007 | Samsung HC-P4752W 47" Rear Projection...

1 Answer

Blurry


Ur tv have a problems call convergence,it dead.The convergence board the 2 STK convergence ICS,and some or all it resistors are dead.All these parts are dead,must be change to solved the convergence problems.The shop will cost u $300-350 for the parts and labors.

May 21, 2010 | Hitachi 43UWX10B 43" Rear Projection...

1 Answer

My Mitsubishi TV is about 12-14 yrs old. The


DLP projection tvs are bulky and have a design flaw in the convergence board the 2 STK convergence ICS alway dies constinely require replacement,if u use about 4 or 5 hours day in and day out.If the old Mitsubishi tv several years since is was repair,u use it alot?If yes,it time to retire it,and buy the refurbish Plama tv.Not,than get the old tv repair.U Know how to solders?Tries Websites Tv repair World.com,Tvrepairkits.com to buy a convergence kit to repair it ur self.U can go to You Tube type in Convergence problems will see a tutoring video in repairing 2 STK Convergence ICS.

Mar 24, 2010 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

Can't correct my red blue convergence manually or by using factory preset...the unit is 7 years old, is my picture tube bad?


You have bad convergence ICs. There are 2 ICs in the convergence circuit, one is for the Blue the other is for the Red. You can buy 2 ICs for under $40.00. Replacing these ICs require soldering and desoldering skills. Sometime, the resistors in the convergence circuit go bad also. Be very careful, there is a very high voltage in a CRT projection TV the voltage is over 30,000 volts.
Best of Luck
Sabre

Feb 23, 2010 | Philips 60PP9202 60" Rear Projection...

1 Answer

Convergnce sony kp65wv600


You can get replacement Ics at the following link which provides free instructions. I would recomend replacing the 4.7 ohm 1/2 watt resistors along with the two STK392-560 Ics as the resistors can get weak over time and that can lead to premature IC failure. Heres the link.
http://servicemanuals.vstore.ca/

Jan 18, 2009 | Sony KP-46WT510 46" Rear Projection HDTV

1 Answer

Sony KP-61XBR200 Convergence problem


STK392-020 ICs are the convergence ICs for your model, you may also want to check the 3.5 amp pico fuses and the 4.7 ohm 1/2 watt resistors as well.

Aug 16, 2008 | Sony Grand WEGA KF60XBR800 60" Rear...

1 Answer

Green double image


you need to replace both convergence ICs they are both STK392-110 and you can get replacement ICs at the following link and they provide free step by step instructions with pictures so you can do the job yourself. Heres the link.
http://servicemanuals.vstore.ca/

Jun 30, 2008 | JVC AV-65WP74 Rear Projection Television

4 Answers

Samsung hcm4216 projection tv blue color problem


first of all in setup mode(where convergence is)select blue screen off.then go to picture mode and either select a set mode,or enter user and manually set contrast,brightness,colour,sharpness and tint.you can acheive near hd quality this way on non hd projtv

Feb 24, 2008 | Samsung HCM4216W 42" Rear Projection...

1 Answer

Toshiba TP50H95 Convergency problem.


Hi. The covergence Ics are mounted on large heat sinks they usually start with STR**** You will need to replace both & check resistors electrolytic capcitors & any circuit protecters on the same pcb as the chips.

Sep 02, 2007 | Toshiba TP50H95 50" Rear Projection...

Not finding what you are looking for?
Toshiba 50H72 50" Rear Projection Television Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

The Knight
The Knight

Level 3 Expert

68368 Answers

Are you a Toshiba Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...