Question about Flat Panel Televisions
Phillips 30inch virtual surround sound system
SOURCE: 15-inch Phillips LCD FlatTV
It could be the AC adapter. That is easy enough to check with a DMM. Turn on the meter, set to volts dc, push red probe into the hole in the output power jack and touch the black probe to the outside of the same jack. Have someone plug the AC cord into a good outlet(one you know has power). If the adapter is working you should see 12 vdc displayed on the meter. There still could be a problem as I recently found an adapter which displayed the correct voltage with no load but little or no voltage with a load. Testing with a load is a problem if you are not familiar with the procedure. Odds are if you have 12 vdc the adapter is fine and you have a short somewhere in the monitor. If you are handy with tools and feel confident, remove the back of the unit and check the fuses in the power supply. If they check OK you probably can't do much more. Unless you are an electronic tech you will need to take the unit to a shop for repair by a qualified tech. Good luck.
Posted on Jul 12, 2006
I just did some research on this problem and found a fix. If your tv has a powersaver feature on it turn it off i put mine on standard and my remote works fine now. weird but it works!
Posted on Jan 20, 2009
SOURCE: how to unlock phillips tv
Try this ..
The Factory code number is 0 0 0 0 If the code has been changed, You can select to reset it using the Setup Code either under the channel blocking or setup code section.
Once there, Press 0 7 1 1
You will be given a message "INCORRECT ACCESS CODE"
Press 0 7 1 1 on the remote again
Next, "enter your new access code" shows on screen.
Now you can enter a new 4 digit code. (write it down somewhere)
Posted on Jan 31, 2009
If you still have the remote that came with the television set you can try to perform a remote reset. If that works than the remote that came with the television as well as the two universal ones should work. I am posting one form of remote reset but the customer service reps at Philips might have a different one that works well on their televisions. There are some variations. Some support representatives will have you press each button on the remote twice:
You have to unplug the television after turning it off. Take the batteries out of the remote control. Point the remote toward the remote sensor (bottom right hand corner of the television set). Press the power button on the remote control and hold it down for 30 full seconds. Next press and release every button on the remote control. Next plug the tv back in and power it on from the power button on the television itself. Replace the batteries. Adjust the volume using the remote control. If that works the problem is solved. If it doesn't work you may need a software update, a new remote control, or repair to the sensor on your television.
To see if your remote control is working look at it through the viewscreen of a digital camera. The digital camera must be turned on and ready to take a picture. Next press a channel button on the remote control. Do you see a bluish white light? If so the remote control is ok.
Posted on Jan 09, 2011
SOURCE: i have one forall remote
Codes and manuals for most One For All remotes are available here: http://www.oneforall.com/support/manual . Select Universal Remote Control and then your specific model to download the manual as a PDF. Note: some of the English only manuals truncate before the code list which follows the Spanish translation for bilingual manuals.
For example the codes for the 8820N are CRT: Philips 1454, 0054, 0690, 1744, 1867 and Magnavox 1454, 1866, 0054, 0096, 0802, 1198, 1254, 1365, 1931, 1944, 1963, 1990
LCD: Magnavox 1866, 0802, 1198, 1365, 1990 and Philips 1454, 1744, 1867
Plasma: Magnavox 1866 and Philips 0690, 1744
Combination units have additional codes. Please note that if the remote is older than the TV, you may need a new remote. Codes are usually limited to those for devices released 6 months or more before the remote was programmed.
I hope this helps. If you can't find your model, please let me know and I'll try to find the code. Just provide your TV type (CRT, LCD, Plasma) and the remote model.
Posted on Mar 18, 2011
Tips for a great answer:
Feb 18, 2015 | Philips 32PFL3403D/27 32 in. LCD TV
Mar 12, 2014 | Flat Panel Televisions
Nov 17, 2013 | Philips 42PF7320A 42 in. Plasma HDTV
Jun 06, 2011 | Dynex DX-L26-10A 26 in. HD-Ready LCD TV
Sep 22, 2010 | Flat Panel Televisions
Oct 24, 2009 | Flat Panel Televisions
Sep 10, 2009 | Flat Panel Televisions
May 07, 2009 | Philips Flat Panel Televisions
Apr 06, 2008 | Philips 32PF5320A 32 in. LCD Television
1,725 people viewed this question
Usually answered in minutes!