Question about Blenders

Open Question

Performance power pro 180w saw critter blade snapped

Hi can any one advise me how to change a blade on my electric hand saw? It has snapped in side. Its a little palm saw.

Thanks

Lisa

model number CLMI805C

Posted by on

1 Suggested Answer

ThaMp3Doctor
  • 8596 Answers

SOURCE: CA 4203 model #, Smoothie 700 Pro

Here's the parts order form:
http://www.focuselectrics.com/finditem.cfm?itemid=4287

-Tha Mp3 Doctor

Posted on Mar 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I ger instrctions on how to put a blade on my electric clippers?


Most common problem is the mounting tongue snapping shut leaving you nothing to mount the blade on. If the tongue is not sticking out so you can put the blade mounting into it then stick a screwdriver behind it and make it come open. The tongue is a flat piece of metal at the front with 2 lines pressed into it. When it is hanging out pop the blade onto it, turn the motor on and snap the blade shut forcefully.

Feb 17, 2015 | Oster PowerMax 2-Speed Clipper Kit

1 Answer

How to put motor and blade sections back together?


There are two phillip head screws holding the blender end together where it came apart. They are hidden under plugs on either side of the imprinted information. Simply drill a hole in each plug and remove them by putting something in the hole (small screwdriver) and pulling them out. Loosen the screws, enough to pull the body apart far enough to insert the blender end back in. Tighten the screws back up and your good to go. I left the plugs out, they don,t serve any purpose.

May 16, 2013 | Cuisinart CSB-33 Quick Prep Handheld...

1 Answer

ELECTRICAL SMELL AND SOUNDS ROUGH


It sounds like you need to replace blade & bearing assembly in the beaker, change it before you wreck the motor.

Aug 23, 2012 | Vitamix 5000 Work Top Blender

1 Answer

My blender wasn't runn ing well then started smoking, i took off the pitcher and saw metal flakes and the blade feels like it isnt turning easily


A small appliance that smokes is a symbol of "needs replacement
It is unsafe and can cause a short circuit on your electrical system that will cost you more than 20 blenders to fix. I just wouldn't use it, something similar happened to me with another small appliance and the deal ended up costing me $6500 in electrical wiring for the kitchen. Think about it.

Jan 29, 2011 | K-Tec Champ HP3 Work Top Blender

1 Answer

Blender is not working after giving electric supply


UNPLUG it and try to turn the blades by hand. Put a drop of alcohl at the point where the shaft comes through the case and turn to loosen the blade. Next, put a drop ov cooking oil at that same place every time you're finished using it.

Dec 26, 2009 | Philips HR1358 Handheld Blender

1 Answer

I am unable to remove the blade, what can I do


the blade is a screw fit on the shaft of the blender,, if you only use one blade just rince the blade under the tap and dry it off before putting it away, the only way to un-screw the blade if its stuck is give it a sudden jolt on the side of the blade with a soft hammer in the same way as it turns,,this may shake it lose,,,not to hard though,,,

Nov 15, 2009 | Bamix Mono Hand Blender - Black...

1 Answer

Broken glass jug on kitchenaid blender model 5ksb2aer4


Look at the underside of the blade shaft. The metal wing nut on the end of the shaft secures the blade assembly to cream coloured plastic blade base. The wing nut also transmits the drive from the rubber coupling on your blender to the blade shaft. The wing nut has a LEFT HAND thread.
The left hand thread ensures the blade assembly does not unscrew during normal blender use.

Firstly disassemble the blender blade assembly. Place a folded tea towel over the blades and hold the blades firmly. If you do not use a tea towel you may cut yourself.

Grip the wing nut with your other hand and unscrew it CLOCKWISE.
Remove the wing nut. You can now remove the blade from the plastic base.

Put the blade assembly in the new jug and offer up the plastic base from under the jug so that the blade shaft protudes enough for you to install the wing nut.

Screw the wing nut ANTI-CLOCKWISE to secure the blades to the plastic base.

Do not over tighten the wing nut; you may have to replace your jug again at some point.

Jun 06, 2009 | KitchenAid KHB300 Handheld Blender

2 Answers

Waring Pro Blender is leaking and blade assembly is loose


I know this is an old, old post, but I could not find a solution anywhere, so hopefully this will help someone. We have a model 51BL25, similar to scottman55's blender, and it had the same problem. There are two separate nuts in the blade assembly. One holds the blade on, and the other holds the seal tight. When the latter gets loose, the blender shakes and leaks.
To fix it, first you have to remove the top nut holding the blade on. I had to get in there with pliers, but a ratchet with an extension would be perfect. This nut is right-handed ("normal"). Once that nut is loose, you can remove the nut and the blade. You will also want to remove the washer immediately under the blade (take note of which side goes up).
Now, you can pull the whole axle out by the wheel on bottom of the blender. This exposes a really thin, flat nut. In my case, this nut had come completely off, so nothing was really holding the seal together at all. Again, make sure you remember which direction the nut goes -- it is not quite symmetrical. That nut is what comes loose when the blender starts leaking. By the way, it is a left-handed nut, so it screws on counter-clockwise ("backwards"). Screw it in tight, then put the rest of the blade assembly back together, and your done. If you have the right tools, it should take only maybe 5 minutes.
Depending on your problem/model, this may or may not solve your problem. Hope it helps!

Jan 28, 2009 | Blenders

1 Answer

Older Vitamix Problem


Hi,

I want you to try this,

1.Remove the blender jar from the blender motor .

2. Check the jar by turning the shaft by hand to see if it rotates easily. .If not, disassemble the blade and ring. Check for obstructions or misalignment. It is better to change the shaft which holds the blade......

If it fails you again, you have to contact with the service center or visit this site
www.vitamix.com/household/service/service.asp

Hope my info helps you,
Thanx for using fixya,
Waiting to help you from your comments.....

Oct 01, 2008 | Vitamix Super 5000 Work Top Blender

1 Answer

Blender blade assembly no longer turns


I had this problem and, after seeing these posts, was motivated to avoid paying the cost of a new blade unit. Here's how it can be fixed:
1. Take a kitchen hotpad and hold the blade (top) side of the unit in your hand as you unscrew the rubber gear on the base. This is a left-handed screw, so you must turn it clockwise, to free it up. This should be doable by hand. Be careful, removing the gear exposes a washer note which side is up, and place both the gear and washer aside.
2. With the blades held in the hotpad, unscrew the top nut, again clockwise. This takes more effort, but it will eventually give way. As this nut comes off, it exposes a rectangular post, to which everything is attached.
3. Remove a washer with a rectangular cutout. Make sure you remember which side is up (I think it makes no difference). This may require some rocking to remove the washer from the round-threaded end. It will come off.
4. Remove both blades in a similar manner. Note their orientation, which is important.
5. Next, remove a rubber gasket. On mine, it has a groove which is asymmetric. I don't think the orientation is important, but, again, you may want to note it.
6. What is left is an axle inside a sleeve. There are no bearings. In mine, I had to tap/drive this out. Take a flat-ended rod (ideas: I used the hex-shaped post end of a nut socket. An old drill bit you don't care about, rotated would also work). Place the unit on the edge of the counter, up-side pointing up, in a way so the bottom end of the axle could fall free when you drive it out. Gently tap the axle through the unit, using the helper tool when the axle is within the sleeve. It will drive completely out.
7. Clean everything. I simply scrubbed the axle and took a small brush to the inside of the sleeve. This doen't need to be perfect, but anything left on either surface may ultimately impair the functioning of the axle.
8. Lubricate the axle with household oil or a dab of grease. You will find that the axle will now slide into the sleeve fairly easily (I had the best luck from the top.)
9. Reattach the base gear, then the top in the obvious order. Everything should spin freely from this point on.
REMEMBER: always use the hotpad whenever you grip the blades and to tighten the bolt on top so that the axle protrudes slightly above the nut.
Good luck!

Nov 02, 2007 | Cuisinart SPB-7 SmartPower Work Top...

Not finding what you are looking for?
Blenders Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blenders Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

eyecam

Level 2 Expert

86 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...