Question about Phoenix Gold Xenon-600.1 Car Audio Amplifier

1 Answer

Hi..phoenix gold x600.1 went into protection

Hi..phoenix gold x600.1
went into protection mode,saw a dirty spot on board,cleaned it.
now,the blue light stays on,but amp does not power the sub,(i do not hear that click when the amp turns on)
any help? should i send it in?
thank you in advance!
rich

Posted by on

  • Anonymous Mar 31, 2014

    i have a phoenix digital car amplifier that is stuck in protection mode and can not figure out how to get out of it thank you

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 109 Answers

Contact Phoenix Gold at 800.950.1449

Posted on Jul 17, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Low level input resistor values ti600.2 left and right channel resistors on board next to RCA in both burned


Hi Dave,

Schematics are tough to come by - but - you may find someone with your model that can help you out in the "Phoenix Gold Phorum" Joining is free - then ask your question and wait for a reply.

Good luck!

Dec 17, 2013 | Phoenix Gold Car Audio & Video

1 Answer

No sound from subs


You need power to the amp. If the light on the amp is not on then your amp is the problem. Get power to it.

Nov 10, 2013 | Phoenix Gold Xenon-400.1 Car Audio...

1 Answer

Can i use a 300 watt amp for 2, 800 watt woofers


yes, but you would not get the same performance as you would if you gave them the suggested power. I have found that it is always better to use a more powerful amp than your subs are rated for (as long as it is clean, high quality, low distortion power). I have had the best luck with name brand amps (kicker,rockford fosgate,phoenix gold,etc...). I hope this will be helpful to you.

Jul 30, 2012 | Phoenix Gold Xenon X10D4 - 10" D4...

2 Answers

Everything did work but kept blowin fuses by the battery. Now a red light stays on, on the amp & the blue/green power lights dont *** on. What should i do?


Check all of your power connections, your speaker connections and battery connections. if all are good and clean (no shorts/wires touching) then try unhooking your speakers and see if the lights come back, if that helps then you have problems with your speakers, if not then amp is bad. I hope this helps ya.

Randy

Feb 17, 2011 | Phoenix Gold Titanium 800.1 Car Audio...

2 Answers

My phoenix gold x200.4 amp turns on but the protect light keep on flashing


  • What does it mean when the LEDs flash on my amplifier?
    With most recently produced Phoenix Gold amplifiers, a flashing/blinking LED is an indication that the unit is in protect mode, usually due to an overcurrent condition caused by an internal short, external short (speakers), or low impedance. Overheating will also cause the amplifier to shut down temporarily.

    If amplifier remains in protect mode, power down the amplifier, disconnect the speakers, and power up again. If LEDs continue to flash, there is probably an internal problem with the amplifier that will require service attention to fix.
  • Sep 23, 2010 | Phoenix Gold ZX600ti Car Audio Amplifier

    1 Answer

    Amp not working, subs just thumping


    U either have a bad ground inside your amp or radio or your rca's on the amp are loose

    Feb 09, 2010 | Phoenix Gold RSD600.1 400W x 1 Car...

    1 Answer

    My phoenix gold xenon 100/2 keeps blinking and putting a loud buzzing sound into my speakers, it went into protect mode, whats wrong with her just got it.


    More than likely a blown output transistor. Phoenix can send you a schematic for that if you email their tech support. Be careful if you decide to work on it yourself.

    Dec 03, 2009 | Phoenix Gold Car Audio & Video

    1 Answer

    My phoenix gold qx 900.1 comes on but goes into protect mode it wont play at all an i wanted to see what could be the problem i had it wierd with 2 kicker cvr 15s at a 1 ohm just runnin off my car battery...


    if your amp is not 1ohm stable you will continue to over load it on those kickers you need to take it easy man not go over board with those 15s get you like one 12 man in good box ported or sealed thats all you need man with that amp

    Nov 05, 2009 | Phoenix Gold QX 900.1D Car Audio Amplifier

    1 Answer

    PHOENIX GOLD RYVAL V1502


    Most the time want happens is the postive wire is not the right gauge or the amp cant handle pusing two speakers you m have to put in two amps try hooking up one sub and see want happens if it dosent die out the amp not strong enough for the 2

    Jul 08, 2009 | Car Audio & Video

    Not finding what you are looking for?
    Phoenix Gold Xenon-600.1 Car Audio Amplifier Logo

    523 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Phoenix Gold Car Audio & Video Experts

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17130 Answers

    Mark Skinner

    Level 2 Expert

    77 Answers

    Jose Velazquez
    Jose Velazquez

    Level 2 Expert

    229 Answers

    Are you a Phoenix Gold Car Audio and Video Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...