How to i connect my head set w/mic - Mirus X2500 Notebook

Connect an external handsfree head set to the phone and check if the mic is working or you are able to be heard well. If so the mic within the phone is faulty . sometimes it can be due to a faulty connection or a block on the mic due to dirt accumulation.
If not it must be replaced with the same type and fitting.

You used the term "plug in my mic". I assume you mean the microsoft mic and head set. one of the best ways to check the headset and mic. is to go onto microsoft live and attempt to leave someonw a voice message. during the message you will get a message that says your mic is not working. also after you finish the voice message attempt to play if back if you do not hear anything then the problem is with your microsoft head set and attached mic. if new take if back to exchange for another one. there could possibly be something wrong with the port connection on you microsoft controller.

problem with you phone software or your mic. try using with a head set and send the result.are helpful or not ?

Please check the booklet/user guide which came with the computer. Does it say that there is a built in mic. If it is there then no need for a separate mic. But if there is no mic then you have to buy a head set with a mic and connect it to the computer in place provided in the computer. It is generally near the audio output.

Your headphone might not have connected properly...

Plugin of speaker and mic should be more carefuly connected if not then cant chat throug mic...

and check internet status while on a chat...

You do not say what your OS is, if your computer is laptop or desktop or what program you want to chat in

Set up Audio

Laptop x webcam/mic x Vista x Yahoo Messenger

If you have an earlier OS, you may have to access your hardware from the Control Panel.

TEST SPEAKERS
Right click on speaker icon in System Tray
Select "Playback Devices"
The speaker icon ( checked as working) and volume level graph should be visible
Right click on the volume graph and click "Test"
Left hand speakers followed by right hand should be heard

SET DEFAULT & TEST MIC
Click "Recording" tab.
To set required mic as default - click on mic font to highlight and click "Properties"
In lower dropbox display "Use this device enable" click OK
Click "Levels" tab and ramp up sliders ( adjust to suit later)
Return to "Recording". Test mic by speaking and make sure volume graph displays
Restart computer
CONFIGURE TO MESSENGER

Open messenger - on top toolbar. Left click ( > ) Messenger > Preferences > Connection - Select 'no proxies' or 'connect direct to the internet' depending on the version of messenger you have
make sure your internet connection and country are correct in the lower two boxes > Apply > OK

Click ( > ) Messenger > Preferences > Calling and Audio
Set mic and speakers to show Default equipment
Run call up assistant to test audio equipment > Apply > OK

Other chat programs are less intensive for audio set up - Skype and MSN can be navigated via the 'Tools' option on the toolbar.

Plugged in? Is it a stereo plug? does your computer allow speaker and mic on the same wire? Does the outlet say Mic or Headset of Both? Had it worked in the past.

Some computers have a place for a mic - some for headset - some might have both. On a desktop, I would expect to find separate connections. Laptop, Id have to look.

A 'stereo' plug will have a tip, ring and barrel connection.

A 'mono' plug will have a tip and barrel connection only.

A stereo plug would allow a mic and head phone connection ujsing a 'common' for the return.

A mono plug would allow either a mic or a headset, not both.

If you could peer into the jack inside your computer, you could tell if it privides for three wire (stereo) or two wire (mono) operation.

I hope this helps ... If I missed your question, please reask.

We are "paid" here by positive comments where we earn "bragging rights" If you are satisfied, please post positive comments

thanks

a

Make sure the microphone and the receiver are still broadcasting/receiving on the same channel.
Check that all of the appropriate connections are right from the receiver to the mixing board are connected as well.
I hope this helps!
God Bless you!

try to change your system just like the one that youve said that its working. it is maybe the system got the problem. or try this one, go to control panel see if your mic is working on your audio software application. set it to make it work by configuring like the volume or anything. hope that helps!


CHARCOIS

1.Check whether your cam has built in mic.
2.if then connect the mic signal cable to the MIC in connector in your sound card.
3.if your webcam doesnt support MIC functions. Connect the head phone with mic to mic/audio slot
4.if you have already connected Mic. then the problem with the sound card settings in the instant messenger menu.
5. Specify proper sound card manufacturer in the audi settings found in the preferences or options or settings menu in IM software.
thank you !