Question about Computers & Internet

2 Answers

My Mitsubishi CP 9550 DW printer i just bought is saying MECHANICAL ERROR

Posted by on

  • oluwato Mar 04, 2008

    Hi Ginko,
    We tried it but the alarm is not clearing on the printer.Kindly assist

  • oluwato Mar 04, 2008

    Thanks a lot. It was a paper that got stuck into it.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a CP9550 DW Printer
I was at home priting the other day the printer had 2 images left on the roll i pressed print the printer started to print but when it had finish the photo had got stuck in the printer so open the front to remove the photo
i then reprinted and all went ok.
I then had to replase the roll/Ink and that was when the proublm happond i press print the rpll comes out of the front of the printer and stays thier it will not go back in then on the screen it says change paper as it as run out but it is a brand new roll.
Can anybody advise.
Steve...

Posted on Feb 01, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 19,396 Answers

Here is the manual. See page 5.
13 ) Mechanical Error.
After removing Error, press the FEED & CUT
button.
14) Mechanical Error.
After removing Error, open and close the door.

regards

Posted on Mar 04, 2008

  • Ginko
    Ginko Mar 04, 2008

    Open all doors on your printer and look for any piece of paper that may be stuck in the mechanics. Close printer back, disconnect the power cable from outlet for 5 minutes and connect it back . Restart all, if all this does not work you may have a defective sensor or other major mechanical problem inside the printer, if this is the case bring printer to nearest service shop.



    regards

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lexmark 4875 finds bad CPU speed


I bought a Lexmark 4875 for mac. It bombs every application when you hit the "print" button. Downloading the fresh driver didn't help, and their support website doesn't address this issue at all.

Mar 25, 2008 | Computers & Internet

1 Answer

I work at home on a network with an HP thin client, I want to hook up a printer but the HP deskjet F-4180 printer I bought has a driver that is too large to for the memory of the thin client


You dont say what Thin Client device your running on but drivers themselves tend to be very small. Make sure your ust getting the driver not the whole HP install (ink monitor, etc).

Mar 19, 2008 | Computers & Internet

1 Answer

Bought new printer is loaded..but always says offline


Right click your printer and go to properties and set it to online.

Mar 09, 2008 | Computers & Internet

3 Answers

Waste tank near full


Hi
The waste ink take is actually just a felt pad that sits under the printer mechanism inside the case and absorbs the ink from your cleanings

Try this:
1 Power off printer
2 Hold RESUME button then press and hold POWER. (The beeper MAY sound once, or may not depending on your model.)
3 Hold POWER and Release RESUME.
4 Press RESUME twice then release both POWER and RESUME buttons.
5 When the indicator lights steady, press RESUME 4 times (for the S900, 3 times for the 8200 apparently).
6 Press power to set data.
7 Print away!

Let me know if that didnt solve your problem

Jan 10, 2008 | Computers & Internet

1 Answer

I reloaded my printer software on my computer and as it were loading a screen came up tha say (runtime error)My printer is about a month old it is a(all in one lexmark 5000 series X5070)


Please unistall all existing drivers for your Lexmark printer driver. remove all the programs unnecessary from windows tra right side down the screen . And Install it again.

Mar 03, 2008 | Computers & Internet

1 Answer

Canon MX700


I had the same problem. Adding twain_32.dll to the Windowsfolder solved the problem. For people who don't want to search for it: Look Here.
Then you won't get this error but one saying to reinstall the printer driver. Just do it and the problem is solved.

Feb 28, 2008 | Computers & Internet

1 Answer

OFFLINE problem - unable to print


Hi,
if your printers saying Offline, it means that your printer is not connected/switched on or detected by the computer.
Try a hard reset or re-installation of the printer itself.
power on/off ( On the printer )while this error message appears.
Check the cable from Printer To Computer.
Mike @ Compurepair.

Feb 23, 2008 | Computers & Internet

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

1,131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

98879 Answers

David Payne
David Payne

Level 3 Expert

14089 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...