Question about Maytag MAV5920E Top Load Washer

1 Answer

Maytag MAV5920AGW not working

Runs for 5 sec only and then stop .

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 156 Answers

Control boars are motor control board is bad

Posted on Mar 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag 5000 series washer control locked light is on and washer wont turn on


1. try unplugging or flipping circuit breaker, wait 10 secs, hold in power/on button for 5 secs, plug back in and see if it resets.
or
2. try tapping on door lock position on front of unit and see if it unlocks unit(lock stuck). hit it hard with palm, but not enough to dent or damage

good luck

Sep 24, 2016 | Maytag Washing Machines

1 Answer

My maytag quite series 100 _ fills with water starts running cycle but stops after about 20 sec _ it does this 3 times then shuts completely off


Sounds like the timer could be a issue . or motor running to hot clean all under and behind make sure no dust ..UNPLUG UNIT FIRST ,....

Sep 28, 2015 | Maytag Washing Machines

1 Answer

How do i rest my maytag bravo x washing machine


sometimes

turn off the mains
hold in start stop or program select or on off or a two button combo
and turn the power on
wait 5 secs then release

usualy this reinits the controller

Dec 01, 2014 | Washing Machines

1 Answer

How to run a diagnostic for washer model MHWE450WW01 Maytag


Starting Error History Software Version and
Diagnostic Test:
NOTE: Washer must be empty and the control must be in the
OFF state.
1. Close the door.
2. Select any one key (except "STOP/CANCEL" and "CONTROL
LOCK" and follow the steps below using the same key:
Press/hold for 2-5 seconds, Release for 2-5 sec, Press/hold for 2-5 sec, Release for 2-5sec, Press/hold for 2-5 sec
3. Upon release, all yellow/green console LED lights will turn ON
for 5 sec.
4. If there are any failure codes stored by the washer, the display
shows them.
Note: The last four errors will be displayed.
5. Press the same key to advance to the next code.
6. After the indication of error codes, the UI, CCU, and MCU SW
version will be displayed.
7. The number of cycles since last clean washer cycle is displayed.
8. All green console LED lights will turn ON for 5 seconds.
9. Next the washer begins the automated diagnostic test.
10.To cancel out of service mode, press the "STOP" button.

Apr 10, 2014 | Maytag Washing Machines

2 Answers

Maytag neptune FAV6800AWW top load washer gets to 32 minutes left and goes no further. It starts to cycle for about 5 seconds and stops for about 35 seconds... over and over and over


Is the machine in Spin Cycle when this is happening? What part of the washer selected cycle does the Cycle Status LED say the machine cycle is in.
If it’s in the Spin Cycle I think you have a clutch issue. Do you take any error codes to the LED console display such as dC or uC?
If you stop the machine in that cycle and do a Spin Only cycle will it complete?
Do you want to DIY the fix? Let me know and I will try to help…..Rich

Feb 26, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag neptune top loading washer with spin problem. spin cycle starts, runs about 5 secs,stops for about 20 secs, runs again for about 5 secs and code of uC pops up on panel. model 6800. Any ideas??


Hey bob_marianne ,

Common problem with the FAV6800AW/FAV9800AW. If you have basic mechanical skills you can fix. It’s just a tight work area to work on the Clutch in this machine. See this post for the details and you can get your $1K machine back in service. Sorry to say a lot of these machines get tossed for a $50 dollar clutch. Let me know if you have any questions after you read the post.

Rich

Jul 16, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag washer stops during spin cycle


it seems like aproblem w motor maybe need to acouple of new carbon brush to fit in motor
i think that because it seems to me from your words that the motor only works w no load
thanks

Jul 11, 2009 | Maytag Dependable Care LAT9706

3 Answers

My washer Maytag Neptune Model MAH3000AWW not working. After push the START button, the "ON" led just light up 3-5 sec then turn off


my washer Maytag Neptune Model MAH3000AWW not working. After push the START button, the led just light up 3-5 sec then turn off

Aug 21, 2008 | Maytag Neptune Washer

2 Answers

SPIN CYCLE


need more information is it top load or front

Nov 19, 2007 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

My maytag top washer want spin out


Check the drain pump. It could be blocked or jammed. Remove the front panel and the pump is easy to access. There will be a hose from the bottom of the outer drum to the drain pump. Remove plug from wall socket before attempting to remove any cover.

Oct 31, 2007 | Maytag Neptune FAV6800AW Top Load Washer

Not finding what you are looking for?
Maytag MAV5920E Top Load Washer Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...