Question about ViewSonic VA720 17" LCD Flat Panel Monitor

2 Answers

Viewsat ultra 2000

My receiver froze completely. it wont change or do anything and the channel is stuck on 1. please help

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I'm having the same problem with my all my Viewsat Ultra 2000. in our bedrooms. A constant freez-up. Now my viewsat HD 9000 in famliy room doesn't freez-up. Please anyone can suggest anything . Other then telling me to ditch it Lol.

Posted on Apr 28, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Viewsat ultra need new bin and a fix for this box freezing and won't unfreez until i turn it off from the back. can someone help me please

Posted on Mar 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ive retuned, re-set, unpluggest and plugged back in and i recieve no channeks still, been like this for months


What is your TV source? The Polaroid LCD-2000 only has a NTSC (analog) tuner. Most OTA stations switched to ATSC signals a few years ago and a converter box is required to watch the TV. (A few low power TV stations still broadcast in NTSC but you need to be fairly close to the transmitter to receive the channel.) If you have cable, check if they have migrated to digital cable (QAM for unencrypted channels). If that is the case, you'll need a cable box.

With a digital-to-analog OTA converter box, you can still lose station reception due to the signal strength cliff. Depending on your area, you may need an external antenna or to check the direction of the antenna. I know I have to rotate the outdoor antenna every so often. It shifts in high wind. Even if the antenna only moves 5 degrees, we will lose the signal for half of the stations.

I hope this helps.

Cindy Wells

Aug 10, 2015 | Polaroid LCD 2000 LCD2000 TV flat screen...

1 Answer

Monitor has power but says not receiving signal and frequency out


Hi, this might be a cable plugged out from your graphics card or from your monitor. Check that first. If the cable fits ok, try changing it with another one to see if it is ok or broken. If it wont do anything, it probabbly needs to go to service for mainboard replacement. Something simillar happened to me too.

Oct 15, 2009 | Gateway FPD2275W LCD Monitor

2 Answers

My computer crashed and when i turn it on, there are 2 beeps


Here are the beep codes for Dell. Count the beeps sequences and compare them to the list.
Dell BIOS Beep Codes:
Beep Codes Possible Causes Corrective Action 1 - 2 No video card detected Reseat the video card 1 - 2 - 2 - 3 BIOS ROM checksum error 1 - 3 - 1 - 1 DRAM refresh error Reseat the memory modules 1 - 3 - 1 - 3 8742 Keyboard Controller error Reseat the keyboard connector 1 - 3 - 3 - 1 Memory defective or not present Reseat the memory modules 1 - 3 - 4 - 1 RAM failure on line xxx Reseat the memory modules 1 - 3 - 4 - 3 RAM failure on data bits xxx of low byte on memory bus Reseat the memory modules 1 - 4 - 1 - 1 RAM failure on data bits xxx of high byte on memory bus Reseat the memory modules

Jan 29, 2009 | ViewSonic VA1703wb Monitor

1 Answer

Channel stuck problem


Hi,
How long does it take (in seconds) before it changes teh channel? Because some TV's, if you have more than 10 channels, have to wait before they change because you might want to change to a higher channel Example:
suppose your TV has 99 channels but your remote has only buttons from 0 to 9. So if you want to switch to channel 7 the TV waits a little before it actually switch to 7 because there might come another nuber after the 7 as the TV doesnot know what channel you wants. 2 to 3 seconds should be the maximum delay.
If it takes more time, check if this can be changed in the menu, often there is a delay possibility in the setup menu.
If teh delay is over 4 seconds and you still have warranty on it, just return it to the vendor.

Jan 16, 2009 | Samsung 21" FLAT CRT COLOR MONITOR

1 Answer

Cannot Dispaly This Video Mode


1. If you have an Nvidia or ATI graphics card your video card is bad.
2. If you have integrated graphics (the video port is part of the motherboard), your RAM is bad.
3. Your computer is packed full of dust because you've never cleaned the GD thing and it's fking overheating.

Dec 07, 2008 | Dell E173FPb 17" TFT LCD Monitor

1 Answer

Proview 3200 HD TV


as you are using the ch3 , have you previously scanned and locked in all the channels for cable,

Apr 25, 2008 | Proview PL913S 19" Flat Panel LCD Monitor

Not finding what you are looking for?
ViewSonic VA720 17" LCD Flat Panel Monitor Logo

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top ViewSonic Computer Monitors Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a ViewSonic Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...