Question about Whirlpool Duet 3.8 cu. ft. Front Load Washer

1 Answer

Front Load washer won't start

Cannot start cycle, get F-01 error code. It is a WFW8300 front load washer. The cancel button does nothing but shut it down. The previous cycle had been stopped early during the final spin using the Pause/Cancel button.

Posted by on

  • Anonymous Mar 18, 2014

    My spin option does not have no spin and I can not hold down prewash I do not have it either

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Whirlpool Master
  • 2,651 Answers

According to site an f-01 relates to a CCU issue, remove power for 2 min and try to reset, if not check wiring to CCU(central control uint) all in tact?? replace CCU

Posted on Mar 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer won't start - sometimes


Jason, take a look at this link and follow the steps very carefully. Were insulated golves. How to Fix an LG Front load washer machine that wont spin

Feb 28, 2014 | Frigidaire Washing Machines

1 Answer

My Kenmore front load washer will not fill--it sounds like it is draining instead. The last load washed did not spin correctly and the clothes were very wet when cycle completed.


Washer Not Filling:


  • Door Not Closed and Locked
    • Front load washers won't fill if the door is not closed and locked. Listen for the door locking when starting a cycle, then pull on the door to make sure the door is closed and locked.
  • Delayed Start Feature
    • Some washers have a delay prior to filling, where the electronic control is checking the dispenser function. This is Normal.
  • Flashing Lights or Error Code on Display
    • When there is a filling issue, the washer may shut off and display one of the following codes: LF, LE, nF, IE, FH, E10 or F20.
    • If the washer is displaying one of the above error codes, then do the hard reset procedure listed below.

If the appliance is not accepting input from the control panel, follow the steps below to reset the control:

  1. Unplug or turn the circuit breaker off for 30 seconds.
  2. Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds.
  3. Press the Pause / Cancel / Stop button twice to clear the display.
  4. Start a short cycle, to check operation of the appliance, by selecting a cycle and pressing and holding the start button until the appliance starts.

Oct 15, 2012 | Kenmore Washing Machines

1 Answer

I have a frigidaire front load washer. When I start a new load it starts with a couple of seconds of water then stops. Does not go into a wash mode, the timer shows it's going thru the cycles but


Hello - This particular issue can be caused by quite a few reasons. Washer could be experiencing a communication error from the main control board, faulty door lock assembly or the timer itself is not operating correctly. Did you notice a humming noise? If so, either the drainage hose/pump is clogged and needs to be cleaned or could possibly have another issue with the door lock assembly. You can also press and hold the start/pause and cancel button together at the same time for approximately 30 seconds to display an error code on the LED. What error code does it display? However, I would suggest contacting a professional to accurately diagnose the washer.

Oct 08, 2012 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Door won't open on whirlpool duet washer frontload


Press the cancel button twice to cancel the error code. There should be an error code flashing -- for example 'F02'.

Nov 10, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

The duet washer has been unplugged overnight. The control locked light is on and won't shut off. Pressing the end cycle button does nothing. What else can we try?


try holding the sop/cancel button for 15seconds, this should reset it but may not completely remedy the problem. after you reset it see if any other lights blink or if any other problems arise

May 06, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Error code UL with 12 minutes remaing on each load


hi,

This error code indicates that an unbalanced load is detected.

if the load is unbalanced, the washer will display this code while attempting to balance the load at the end of the wash cycle and before the final spin. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, open lid and redistribute the load. Close lid and press Start/Pause.


If the washer is not level, the washer may be more sensitive to unbalanced loads. The washer must be level from side to side and from front to back. The front and rear feet must be in firm contact with the floor. Make sure the locknuts are tightened.

If Power/Cancel or Pause/Cancel does not work
Unplug the washer or disconnect the power for one minute.
Plug in the washer or reconnect the power.
Re-select the cycle and press Start/Pause.

Sep 06, 2010 | Maytag Bravos MTW6600T Top Load Washer

2 Answers

Error code f22 whirlpool duet wash cycle


f22 is a door lock error try this hit cancel turn your dial to another setting, hit start and once it starts hit cancel again and it should unlock. thats what i did anyway.
If you're getting an F22 error, you will want to check anything to do with the door latch switch.

Mar 14, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Intermittant trouble with code d 11


Answer Duet HT®
duetht_f22_actualsize.jpg
Duet®
duet_f_dl_actualsize.gif Duet SportTM
duetsport_f_dash_22_actualsize.gif
This error code indicates that the door is not locking.
Is the washer door firmly shut?
The door must be completely closed for the washer to operate. The door may look as if it's closed, but it may not be latched. Open the door and firmly close it.
Were you washing a large load?
Before you close the washer door, check for laundry items sticking out beyond the door opening. Leave enough space in the washer to allow the clothes to freely tumble. Reduce your load size if needed.
fl_doorseal.jpg To remove the error display, press Pause/Cancel twice.
hcz_003_web_env1.gif

If Pause/Cancel does not work:
  1. Unplug the washer or disconnect the power for one minute.
  2. Plug in the washer or reconnect the power.
  3. Re-select the cycle and press Start.
NOTE: If the error remains on the display, and all of the other conditions above have been checked, call for service.

Dec 19, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool duet front load washer


Select PAUSE/CANCEL twice to cancel the cycle. Select
DRAIN/SPIN if there is excessive water in the washer.
Re-select cycle and select HOLD TO START. If the problem
remains, call for service.

Sep 28, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

14 cycle front load washer fridgidaire


press cancel. (turns off washer)
press start/pause (wake up)
hold cancel and start/pause 10sec

last error code will come up.

E47 door lock error

check wires connections to the door lock..

replace door lock..

hope it helps

Aug 08, 2008 | Frigidaire ATF6000ES Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...