Question about Hobart A200 Stand Mixer

2 Answers

Hobart A-200 serial # ?

I just bought a Hobart A-200, older mixer. It seems to run fine but I have seen that others have received info on mfg date from their serial numbers. Any info is welcome, Thanks!

SN 1687930 (or C)
Spec 16861

Posted by on

  • Anonymous Jun 12, 2008

    manual to put parts together



  • Anonymous Jun 13, 2008

    manual

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 135 Answers

Hi. Your mixer was manufactured in 1967. If you plan on keeping it, take the outer cover off, gently remove the two metal dust caps with a small screwdriver and look into each opening with a good flashlight to determine the quality and amount of grease in the trans. case.

Ideally the grease should almost fill the space with no oil visible. If you need to look further, I suggest that you open up the transmission cover, to determine the condition of the grease that lubricates the transmission. If you find that oil is seperating from the grease. you would do well to remove all of the oil and old grease and replace it with either Shell Darina EP-2, or Chevron FM ALC EP-2 grease. It's a messy job, but it will add years of life to your mixer.

Check the planetary seal, remove, clean and regrease the planetary gearing. With a mixer of this age, you never know if it has ever been serviced since it's manufacture or not. The grease must totaly encapsulate the trans. gears. As the grease breaks down it's level lowers and it leaves some of the upper gears without lubrication, and will result in preventable wear.

Good luck! If you found this solution helpful, please rate it. ricardok45

Posted on Feb 26, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

I'll see if theres any info tomorrow.

Posted on Mar 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW OLD IS MY MIXER


The Hobart A-200 is an 80's product. These first came on the market around 1985. There is no way to date the one you have without examining it.

The best estimate is 25-30 years old.

Sep 22, 2015 | Hobart A200 Stand Mixer

1 Answer

Age of mixer Serial # 11-064-362 A-200


Id contact Hobart. the serial # doesnt use a date code. Hobart Contact Us

Sep 02, 2015 | Hobart Food Mixers

1 Answer

Older, (1950) Hobart A-200 runs in first gear no matter where the shifter is set?


My Hobart had a switch on the side to change Gears... 3 Different Speeds

Apr 11, 2013 | Hobart Food Mixers

1 Answer

Hobart A-200 mixer (OLD!) runs hot & shuts down.


You have killed it by overloading the bowl. Hobart recomends no more than 65% bowl capacity on doughs & 75% on batters or icings. Replace the motor or the whole unit

May 25, 2009 | Hobart A200 Stand Mixer

2 Answers

Hobart A-200 First Gear is Having Trouble


If the mixers are older the dive key shaft,spring or key are broken,if they are newer the key is sheared.Also check the nuts near the beater shaft and make sure there not too tight.

Nov 13, 2008 | Hobart A200 Stand Mixer

1 Answer

A-200 mixer oil leak


the trans uses all grease today hobart uses mobil lith aw-2 you can get the seal from any hobart office.

Oct 19, 2008 | Hobart A200 Stand Mixer

1 Answer

Age of a-200


There is a two letter code that translates to the month and year. You would need to call Hobart to translate. 1-937-332-3000

There are hints to the age, first two digit of the S/N is the factory. "11" are the older ones, spec vs ml on plate, type of power switch, bowl gaurd....

May 16, 2008 | Hobart A200 Stand Mixer

1 Answer

Hobart 20 QT. mixer (HL 200) will not operate on a GFCI receptacle.


you need to replace the gfci,the older gfci's interpret these frequencies as a shock hazard and shut off power to the circuit.you can buy @hobart, part#913053, that should solve the trip problem. dont forget to vote thanks monomoy

Apr 05, 2008 | Food Mixers

1 Answer

Hobart A-200


goto this site http://www.hobartcorp.com/default.aspx. you will find a parts list/view. before ordering any parts i would call your local hobart branch because the part numbers have changed.make sure you have the ml number or spec number found on the data plate before hand so youll get the right part numbers.any questions let me know,i repair alot of these mixers im a hobart service tech.

Nov 12, 2007 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Hobart A200 Stand Mixer Logo

892 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Pieter Vleeshouwers

Level 3 Expert

1524 Answers

yadayada
yadayada

Level 3 Expert

63291 Answers

Lawrence Oravetz

Level 3 Expert

7928 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...