Question about Canon PIXMA MP830 All-In-One InkJet Printer

1 Answer

Won't power up

Recent wind storm resulting in multiple power outages in one days time and the next day I couldn't get the printer to turn back on. Plug is good power supply is hot it just won't turn back on. I tried unplugging for a short duration but that doesn't do anything. Any advice?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I fixed it! Instead of 20 minutes I unplugged it for about 4 hours and everything is working fine. It's a moody ol' girl.

Posted on Mar 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After years of using the same setup I get a communication error on my Epson r290.


Sounds like you have multiple drivers. On the MAC, go to the printer set up window in system preferences and select the r290, then go to the "-" minus icon at the bottom to dump the r290 from the list. Restart the computer with the r290 connected and see if the system recognizes it again in the preferences window. Hit the + icon to add it. Hope this helps.

Sep 04, 2014 | Epson Stylus R290 InkJet Printer

1 Answer

MUTIPLE LEXMARK PRINTERS RUNNING ALL GETTING 976:0 SRV NET ERROR CODES


this network error being created in multiple units would be caused by a couple of things one is that you had a stormy day , and electrical storm or a power surge that has corrupted the nvram chips on the network cards they will need to be replaced. it is always a good idea to install surge protectors on your electronics

Feb 10, 2010 | Lexmark Optra T616 Laser Printer

1 Answer

Will not power up after an electrical outage


unfortunately you probably have to replace the fuser controller board and/or the low voltage power supply.

if this was a result of an electrical storm, it should be covered under your homeowners or renters insurance ( after your deductible of course ).

Sep 15, 2008 | Dell 3100cn Laser Printer

1 Answer

LED lights


http://welcome.solutions.brother.com/BSC/public/us/us/en/faq/faq/000000/000100/000070/faq000170_012.html?reg=us&c=us&lang=en&prod=hl1440_all&Cat=11



If you see any of these service call indications, turn off the power switch, wait a few seconds, and then turn it back on and try to print again.

Note
    They will tell you if it is fried

Oct 02, 2007 | Brother HL 1440 Laser Printer

1 Answer

Power outage=shut down


You do not say your location- so this may not be relevant to you. If in UK - check the power cord fuse. If it is a model that relies on an external power supply- try to find anther of the same specification. Other than that presume it has died

Jul 09, 2007 | Canon PIXMA iP4300 InkJet Photo Printer

2 Answers

How to correct error message sram error missing E?


Hate to say this but most likely the Print Engine Control Board has failed.

May 09, 2007 | Xerox Phaser 7300DN Laser Printer

3 Answers

Hp LaserJet 5 si


Check the print processor settings in the advanced tab of the printer properties. This should be set to Winprint, and not anything else.

May 01, 2007 | HP LaserJet 5si Printer

Not finding what you are looking for?
Canon PIXMA MP830 All-In-One InkJet Printer Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts

kakima

Level 3 Expert

96372 Answers

old marine
old marine

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...