Security hello guys ive just installed my router works fine but it never came with istall disc do you know how i can put securtiy on it ie pass word it to stop others using it kind regards kieron

hmm open up a web browser ie(firefox or internet explorer) at the top select Tools/Options/Securtiy and add exceptions that enable you to install programs and whatnot.

Hi Friend,
When you are tring to connect in wireless it will ask for password,please follow the below steps and get the security key of your Router

Step 1:Connect the Modem to Router (in the Port named Modem) and take another ethernet cable abd connect one end to the Router(in the port named Wired) and other end to any one of your computer

Step 2:Open an internet explorer and type 192.168.2.1 and click on Enter button in the keyboard

Step 3:Now you will be able to see the belkin router setup page

Step 4:On your left hand side click on Security,it will prompt for a login password,leave it blank and click on Submit.

Step 5: In this page you will be able to see the security key or PassPharse,please make a note of it and type the same when its asking for security key

Regards,
Aysaam

Hello
First you will need to have the install disc for your card.Install driversoftware from cd or dvd, following directions.Once installed you should see a new hardware device has been found notification.

Next you will need to configure your card with the routers wep key or wireless security key.I am assuming wireless is activated on your router.Should see a light on the router lit under wireless,or a symbol.
1 start pc then start internet explorer.
2 Type in the top bar of ie 198.162.1.1 or 198.162.1.0 hit enter.
3 This should bring you to the routers home page.usaername=admin password=password or admin
4 Find your wireless tab or settings page looking for security area.
5 Find your wep or wireless security code,write this down.
6 Log off of router.
7 Go into network cards configuration program and put this wep code into the area provided.
8 Software may have found it automaticly, it just needs this code.

If you cant connect to router at step one use a ethernet cable from your pc to the router to log on.

Hope this helps.

At any cost do not disable the NAT - because thisis the feature which allows multiple device to work with router

So only option you've got now is to reset the router. It should be at the rear end of the router. Hold onto it for 30 seconds, u'll see the light flash and router reboot

Once you've done with that - configure router and make it work.

And as of for the Xbox Issue try these steps:

1 - Assign a Static IP address in the Xbox:
- Go To Network Settings - Configure Network
- Change IP settings to Manual
- IP Address: 192.168.2.45 Subnet Mask: 255.255.255.0 Gateway: 192.168.2.1
- DNS settings to Manual
- Primary DNS: 192.168.2.1 Secondary DNS: 4.2.2.2

2 - with any of the Wired Computers
- open IE - type - 192.168.2.1 - u'll get the Router Interface
- left hand side in the list of options
- click Firewall - leave password blank - disable and apply changes
- click Virtual Servers;
- under enable place a checkmark
- description : Xbox, Inbound Pot : 80(if there are two boxes here duplicate in both the boxes), Type: TCP, Private IP: 45, Private Port: 80
- So Similarly fill up the table for these following Ports
TCP: 80, UDP: 88 Both(TCP&UDP): 53, 3074

Additional Note:

If u've a DSL connection, call ur ISP and make sure ur modem is bridged and the NAT is disabled

put in the disc again and run the installation and when it asked me to run the installation it asked me what channel I wanted it on but the default was 11 so I kept it there, just try to set it up again

Try to check proxy server to IE. Just uncheck proxy server..

go to wireless device and re-configure it

Ok make sure your PC is connected to the router with a network cable for programming.
I noticed you said 192.168.1.1. I see an extra period just wanna make sure your typing it in correct
192.168.1.1

Ok so make sure the cable modem is plugged into the WAN on the router... Now connect another ethernet cable to the PC and the router. Reset the modem and router... wait a few mins and try to connect to the programming setup.
User name= admin Pass=admin

Check ip address of your pc. Go to DOS Prompt, type ipconfig then click enter. Look for DEFAULT GATEWAY(that will be your router ip address). Open your browser and type the default gateway on the address field(example: 192.168.1.1). That will take you to your router page. You can set up security there.

You need to setup security through the web browser interface. You can connect to the web based interface by pointing your browser to the IP address of the router. U will be asked for a username and password after which there is a security tab where in you can set WEP/WPA encryption and password, etc.