Question about Washing Machines

1 Answer

Kenmore washer: no cold water

Re: Kenmore 80 series 110.26822692
I get plenty of hot water, and just dribbles of cold water. I've checked the following:
1. the cold water pressure is good.
2. the cold water hose is not blocked.
3. the cold water wire filter- between hose and washer is clean.

Posted by on

  • 2 more comments 
  • Anonymous Jun 07, 2008

    Water valve good(switched hot connector on

  • timmercer Nov 22, 2008

     have the same problem.
    Hot good cold dribbles out.
    As it is dribbling out if I turn cold water off at the valve and turn back on the water comes out.

  • Anonymous Mar 14, 2014

    kenmore 80 series hot water gushes out underneath washer

  • Anonymous Mar 15, 2014

    Hot water reduced to a dribble.
    Cold water floes ok.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Washing Mach... Master
  • 2,651 Answers

Easy way for me to determine problem is reverse the hoses on the machine still no cold??? should be no hot now!! in which case you have a bad water valve no cleaning need to replace

Posted on Mar 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore Series 80 heavy duty has a water flow problem


Check the water inlet valve. Remove the water supply hoses and check the small screens inside the water inlet valve. Make sure they are clear of rust or debris. The solenoids can be tested using a multimeter or ohmmeter. Check for continuity. A lack of continuity indicates a bad solenoid and the water inlet valve assy will need replaced. I will attach a photo for reference. Sorry for your trouble and I hope this helped. Best wishes.

a62279d.gif

Sep 06, 2009 | Washing Machines

2 Answers

Cold water dribbles in rinse cycle, hot and warm water fine


If you check the warm water flow you'll likely find it is HOT...and not warm. Check the faucet end of hose to see if screen is clogged. Should be screened washer with the dome portion of the screen facing out at you. Remove it and clean with brush to remove grit or scale from screen. If you find nothing there you need to replace the water fill valve located at the other end of the hoses. Good Luck

Aug 23, 2009 | Kenmore 22422 Top Load Washer

1 Answer

My Kenmore series 80 washer's cold outlet doesn't work


Hi, It does sound like the inlet valve is bad. If the screen inside the inlet vavle is not plugged, you will most likely need to change the valve. If you will send me a model #. I can tell you how to get to the valve for replacement.

Thanks
Vic

Jul 26, 2009 | Washing Machines

1 Answer

Won't complete cycle, stops at rinse. and can't get hot water.


Are you on well water? turn off the cold water to the washer and clean the screen filter out. do not leave filter out.
the machine probably has a cold only final rinse so it won't work properly.

Mar 22, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Washing machine won't heat water


it sounds like the hot water supply hose on the back inlet water valve is not opening up,to check it switch the hoses,cold on hot,and hot on cold,put the washer on fill cold,if hot water comes out you know it's the water valve-mike

Mar 21, 2009 | Kenmore 80754 Top Load Stacked Washer /...

1 Answer

Kenmore washing machine does't fill with water only dribbles


Try disconnecting the hoses from the rear of the machine and see if the screen filters are clogged up and also make sure that their is plenty of preasure and volume of water when you turn on the hoses unhooked directed into ther drain. This is likely your problem as it is unlikely both the hot and cold fill valves went or bad out at the same time. 

Dec 20, 2008 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore 80 Series will not fill up with water


if your washer will agitate when set to fill but not fill, then your pressure switch is bad.
also you may want to check and see if you are getting both hot and cold to your washer.

Nov 24, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 80 series washer


Sounds like you need a mixing valve.

double check for water from the source.

Jun 04, 2008 | Washing Machines

1 Answer

Kenmore 80 series top loader the washer will not fill with cold water only hot water


Yes patrick you can try removing the cold hose from the washer, look inside the valve for a metal screen. If it has sediment blocking it remove screen, clean it and reinstall. If still no water replace inlet valve.

Dec 01, 2007 | Kenmore 24902 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...