Question about GE Profile Harmony DPGT750GC Gas Dryer

1 Answer

Touch Screen Panel

When my dryer turns on the flat panel has a bunch of black lines and we cannot do anything. Plugging and unplugging the machine used to work. Now nothing helps.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 156 Answers

Control panel bad

Posted on Mar 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

FEQ1442ES1 works but no heat


Instructions

1Turn off and unplug the dryer. Since you need to remove the front panels and expose the electrical wiring of the dryer's buzzer you should turn the dryer off and then unplug the machine to avoid shocks. Once the dryer has been unplugged, turn its dial to the "on" setting to make sure the dryer is completely powered down.
2Locate the buzzer. The best way to locate the dryer's buzzer is to check the machine's schematic or manual. The buzzer is usually located behind the front panel of the machine. In some cases the buzzer is located behind the dryer's back panel. Dryer buzzers are generally small black boxes that are wired to the timing device.

Jan 09, 2013 | Dryers

1 Answer

Need to convert from natural gas to propane


Take 3 screws out of bottom side of Z shaped metal part on the back of the dryer's top. Stand in front of dryer and use the palms of your hands to sharply push dryer top back about 2 inches and lift top off. Open door and remove screw at 4 and 8 O'Clock position. Remove control panel (ususally 2 screws and a bunch on retaining plastic parts along the top side) and set on top of dryer or unplug electrical plugs and set aside. Remove screws at top of front panel. Unplug light bulb and door switch. Tilt front panel forward and lift off bottom tabs, then unplug moisure sensor wire at bottom, allowing front panel to be set aside. Remove 4 screws at sides of drum support assembly, lift up and off. Release belt, and remove drum. (easier to do if flat metal part originally right behind control panel is removed first) Use belt as a handle and lift drum out of dryer, allowing access to burner assembly. Change burner orfice and regulator blocker. Re-assemble and test.

Nov 18, 2011 | LG Dryers

1 Answer

I need to know how to replce the igniter on this dryer If there is a detailed repair on how to locate and open the cabinet


Hello,

To replace the ignitor,UNPLUG THE DRYER,use a flat blade screwdriver placed between the outer edges of the top/front panel and pop the top up,then lift the top back against the wall(its hinged and wont fall off),remove the wires to the door switch,use a digital camera and take picture of wires so ya know where they go,in the top corner(s) of the front panel will be a screw that holds the front panel to the sides of the cabinet,remove those screws and tilt the front panel out about 6-8" and lift the panel up and out. The ignitor will be in the burner tube on the lower right side of the base frame,unplug the ignitor and remove it,install new one(the plug is keyed and will only fit in one way) Reassamble in reverse order.To reistall the front panel their are brackets in the base frame,slip the notches of the front panel into those brackets and line up the pins with the holes in cabinet.WHEN REPLACING THE IGNITOR ONLY HANDLE BY THE CERAMIC BASE AND DO NOT TOUCH THE FILAMENT

Good luck
i hope this helps ad if it does please give me 4 thumbs up

Gene

Jul 28, 2011 | Magic Chef CYG3005AWW Gas Dryer

1 Answer

How can I disconnect the alarm when the drying is finished?


  • Turn off and unplug the dryer. Since you need to remove the front panels and expose the electrical wiring of the dryer's buzzer you should turn the dryer off and then unplug the machine to avoid shocks. Once the dryer has been unplugged, turn its dial to the "on" setting to make sure the dryer is completely powered down.

  • 2

    Locate the buzzer. The best way to locate the dryer's buzzer is to check the machine's schematic or manual. The buzzer is usually located behind the front panel of the machine. In some cases the buzzer is located behind the dryer's back panel. Dryer buzzers are generally small black boxes that are wired to the timing device.

  • 3

    Pull the buzzer's wires. The most simple way to deal with a buzzer is to pull the wires that run into the buzzer. The wires should pull free with a firm but careful tug. Once you've disconnected the wires from the buzzer simply run a good amount of electrical tape over the ends so that no live wires are exposed. If you want to get the wires out of the way, tape the wrapped wires to the top or side of the dryer panels.

  • 4

    Test the machine. Once you've yanked and taped the buzzer's wires, plug the dryer back in and turn the machine on to test the buzzer. If the machine still buzzes at the end of the cycle then you removed the wrong wires. However, chances are that the machine will finish its drying with a quiet whimper instead of a loud buzz.


  • Feb 17, 2011 | Miele Novotronic T230C Electric Dryer

    1 Answer

    Will not turn on


    The most common cause of an ELECTRIC dryer that will not turn on, is a blown thermal fuse or bad power cord. If the voltage at the wall receptacle is correct (220-240VAC), check the voltage again at the terminal block where it connects to the dryer. Make sure you UNPLUG the dryer and remove the the small access cover where the power cord is installed. Plug the dryer back in and take a voltage reading across the RED and BLACK terminals for the same voltage reading. If good, the problem is INTERNAL to the dryer. If bad, you need to replace your power cord.

    NOTE: If the wires are not color coded, the two HOT leads are the LEFT and RIGHT wires. The center wire will be NEUTRAL or GROUND.

    If the problem is internal, and if the model number is correct, the thermal fuse can be accessed by following these steps:

    1. UNPLUG dryer. Dangerous voltage is still present inside a dryer even with the unit turned off.

    2. Turn the dryer around so you can access the rear panel. Remove the dryer exhaust vent hose.

    3. Remove the rear panel of the dryer and set aside.

    The thermal fuse is a small plastic looking component with two wires attached on the blower fan housing on the lower LEFT-hand side of the dryer. Disconnect the wires before taking any resistance checks. If the fuse is good, it should read something close to zero ohms. If bad, you will read an infinite reading. These fuses DO NOT reset and must be replaced if bad.

    Another cause of a dryer that will not turn on, is a broken door switch. An easy method to test the switch is to open the door and press by hand. If the dryer drum light is working, you should be able to toggle the light on and off. If the switch is found to be defective, it can be raplaced by following these steps:

    1. Make sure the dryer is UNPLUGGED.

    2. Remove the dryer lint screen.

    3. Locate the two screws under the lint screen and remove.

    4. With the screws removed, the top panel will not lift up, exposing the dryer door switch.

    5. Disconnect the door switch connector plug using a small flat blade screwdriver to release the connector tabs.

    6. Remove the defective switch by loosening any screws holding it in place and re-install a replacement.

    Make sure the connector plug is reconnected and lower the top panel back in place. Test operate by plugging the dryer back and turning the dryer on. If op tested okay, reinstall top panel screws.

    Replacement parts can be purchased at any of the following websites:

    searspartsdirect.com
    pcappliancerepair.com
    appliancepartspros.com
    repairclinic.com

    All these sites are reputable and have competitive pricing, so shop and compare. The first three sites listed also have helpful exploded view parts illustrations that you can use to locate and properly identify any parts you may need. If the model number is correct, the part number you may need are as follows:

    Thermal Fuse - part number 3392519, listed as item 23 under the "Bulkhead Parts" listing.

    Door Switch - part number 3406105, listed as item 10 under the "Cabinet Parts" listing.

    The following link can give you some added advice on how to troubleshoot most common electric dryer problems:

    http://www.fixya.com/support/r3574266-thorough_dryer_advice

    If you have any questions about these repairs, please post back and let me know. I hope this helps you.

    Sep 22, 2010 | Roper REX4634KQ Electric Dryer

    1 Answer

    All the lights on front panel on my frigidaire FEQBB30DS0 dryer


    Sounds like one of the buttons is stuck. You may have to replace the touch keys panel

    Sep 04, 2009 | Dryers

    1 Answer

    Dryer blowing cold air


    UNPLUG the dryer. This model you need to remove the two screws under the lint screen. Now use a flat blade screw drive and insert it in the gap between the top and the front panel and pry the top up. Now locate and remove the screws on the inside of the front panel in upper corners. The front should lift off. You will see the ignitor attached to the burner. You can try and replace the ignitor without removing the burner. Sometimes it is just as easy to remove the burner. Make sure the gas is shut off before removing the gas fitting on the gas valve. Be carefull and DO NOT touch the black part of the ignitor with your hand. It could ruin the ignitor with the oil on you hand.
    If I can assist you further, please let me know.

    Thanks
    Vic

    Jul 05, 2009 | Whirlpool LGR5636L Gas Dryer

    1 Answer

    Dryer not venting properly


    Unplug the dryer.
    Raise the top lid.
    Remove the front panel.
    Inspect the blower wheel attached to the motor.
    It is probably turning on the shaft.
    If so, replace the blower wheel.

    If not, dig the lint out of the vent between the wheel and the rear of the dryer.

    Mar 12, 2009 | Maytag Dryers

    1 Answer

    Do gas dryers have heating coils whirlpool


    OK STAY WITH ME...LIL MAMA AND I WILL TALK YOU THROUGH..OK..FIRST UNPLUG THE DRYER...NOW GET A PUTTY KNIFE,,OR A SCREW DRIVER...AND STICK IN IN THE BOTTOM PANEL,,YOU WILL FEEL TO CLIPS PUSH STRAIGHT AT THE CLIPS ONE ON LEFT AND ONE ON RIGHT END OF PANEL..UNPLUG UNIT,,YOU SEE A WHITE FUSE IN FRONT OF YOU WITH TWO WIRE COMING OUT,,JUST REPLACE IT ,,OR FOR NOW AND THIS IS TEST ONLY PUT THEM TOGETHER WITH OUT FUE AND MAKE SURE THEY TOUCH NOTHING,,RAP A LITTLE TAP SO THEY DONT TOUCH ANYTHING,,,PLUG UNIT IN DO YOU HAVE HEAT NOW,,,LET ME NO ONTHEJOB,,,ALWAYS BE CAREFUL...

    Jan 06, 2009 | Whirlpool GGQ8831L Gas Dryer

    1 Answer

    Heating element


    IF you have the dryer pictured above,

    You'll have to remove the console (screws behind covers on endcaps.) Then flip the console up and remove three screws holding the top panel down. Slide the top panel toward you and remove. Disconnect light and door switches (top front left.) Remove the toe panel (putty knife on two tabs top left and right.) Open the door and remove the lint screen. Close the door and remove the metal triangular box around the lint screen. Remove the screws at each corner of the front panel. Lift and rotate the front panel slightly clockwise to get the basket off the rollers. Reach under the basket to disconnect the belt from the motor. Lift the belt and the basket out of the machine. You can now reach the heater on the bottom left.

    Before you do anything, unplug the machine, remove the lint screen, toe panel, and metal box and check the white plastic thermal fuse on top of the blower housing with an ohm meter. It should read less than one ohm.

    Mar 09, 2008 | Kenmore 63942 Dryer

    Not finding what you are looking for?
    GE Profile Harmony DPGT750GC Gas Dryer Logo

    Related Topics:

    101 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GE Dryers Experts

    Richard Roth
    Richard Roth

    Level 3 Expert

    9472 Answers

    John Tripp
    John Tripp

    Level 3 Expert

    4630 Answers

    gbob59

    Level 3 Expert

    2963 Answers

    Are you a GE Dryer Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...