Question about Ariston Technologies LI640S Dishwasher

1 Answer

Ariston dishwasher no water entering dishwasher through inlet hose

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 734 Answers

If there's no water entering your dishwasher, check these:

Water-inlet valve
Float switch
Water-inlet valve
The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely
replace it. It's usually located behind the lower access panel on the left or right side. It's the device
with the main water line (usually copper) from the house, a rubber tube to the dishwasher, and two
wires attached to it.

Float switch
The float switch is a small electrical switch that's located right below the dishwasher "floor."
Above the switch, on the inside of the dishwasher, is a plastic cylinder that floats up as water fills
the dishwasher. If this switch is defective, or if the plastic float gets caught or trapped in the raised
position, the water can't enter the dishwasher. If the float switch is defective, you need to replace it.

Posted on Dec 12, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

AEG OKO FAVORIT 40300 When switching dishwasher on no water is flowing into the the dishwasher?


It should first be checked for correct water inlet hose with safety valve. After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running. If the water inlet hose starts to leak during this operation, the safety valve cuts off the running water and the draining pump in the dishwasher is switched on. If the inlet hose with safety valve working correctly than could be some of following faulties.

  • The door of the dishwasher is not closed properly.
  • Mains plug is not plugged in.
  • House fuse in defective.
  • In the case of dishwasher models with start delay
    timer: A start delay is selected.
If you look at the lower electrical diagram then you can see that all electrical components are located in a circuit inlet valve which can be also faulty.

  • ON/OFF Switch
  • Door switch
  • Program controller (Timer)
  • Pressure switch
  • Inlet valve
  • Float switch
  • Wiring between all this components

Dado
25866319-uhof12xdp2cjm4y1mihcgk0l-5-0.jpg

Sep 15, 2015 | AEG Dishwashers

1 Answer

What dose check water meeans


it means it cant feel if any water is entering the machine. either due to the water being turned off somewhere , the inlet hose not connected or the inlet flow sensor has failed

Nov 23, 2014 | Bosch 24 in. SGS43C02 Classixx Built-in...

1 Answer

Aeg 60870 dishwasher water not getting in. Error code.10


The most common cause of a fault "i10" is closed valve on the water supply line. So this failure indicates a problem with filling of water.
Possible error causes:
Closed water tap, Inlet valve faulty, inlet hose bent, softener system clogged, pressure switch or pressure switch hose obstructed or leaking, wiring from pressure switch to printed circuit board (PCB), wiring from inlet valve to PCB and finally PCB.

Dado

Oct 04, 2014 | AEG Dishwashers

1 Answer

The ariston washing 125 show h2o on the scrim


The washing machine fails to load water (The wording H20 is displayed).
  • The water inlet hose is not connected to the tap.
  • The hose is bent.
  • The water tap is not turned on.
  • There is a water shortage.
  • The water pressure is insufficient.
  • The START/RESET button has not been pressed.

Dado

May 29, 2014 | Ariston Technologies AW125NA 13 lbs. Load...

1 Answer

Ariston h20 errors


The washing machine fails to load water (The wording H20 is
displayed).


• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.

Dado

Jan 14, 2014 | Ariston Technologies AWD 129 NA Washer/...

1 Answer

Omega dishwasher


You should actually disconnect the hose from the dishwasher end and check that water can go through it, otherwise it could be a faulty anti-flood device in the hose.
Failing this, you may have a faulty inlet solenoid.

Jun 01, 2013 | Dishwashers

1 Answer

No water entering the dishwashet


Check electic water inlet valve screen on lower left bottom of dishwaser, follow the inlet water line to locate the valve, turn off power, and water, reremove inlet water hose, and valve hose, check inlet screen for sand, wash as needed. re-assemble in reverse order,

Oct 13, 2012 | Dishwashers

1 Answer

I have an Ariston 640 LI dishwasher and no water seems to be flowing into the dishwasher


hi there Mellisa, Is the tap turned on? if it is in may be the inlet valve at fault you will need to have it checked it see if the valve is recieving the open command from the controler. let me know if this helps, regards
Gary

Oct 16, 2011 | Ariston Technologies LI640S Dishwasher

1 Answer

Water is not entering dishwasher what would be problem


Hi

When the Dishwasher won't fill you'll need to check for the water inlet hose, the water inlet valve and the float switch assembly. When the water fills your dishwasher, a float rises along with it. As the float reaches a certain threshold level, it shuts off the flow of water, thereby preventing a leak. Sometimes the float can get stuck in the wrong position in your dishwasher, and it can prevent your dishwasher from filling. Sometimes it can happen due to float valve and on other occasions due to float switch. Inspect the water hose coming to the dishwasher for any blockages. If the hose is not clogged then check the water inlet valve for any clogs, if the water will not even fill for few seconds then certainly the water inlet valve is bad and should be replaced. You can also use a multimeter to check continuity on inlet valve. If you don't get any value on the multimeter then you'll need to replace the water inlet valve assembly. However, if the valve is fine then the float switch assembly should be replaced. Hope this helps... Please post back if you need more information.

Daniel

Aug 04, 2011 | Dishwashers

1 Answer

Water not entering the dishwasher


Hi

When the Dishwasher won't fill you'll need to check for the water inlet hose, the water inlet valve and the float switch assembly. When the water fills your dishwasher, a float rises along with it. As the float reaches a certain threshold level, it shuts off the flow of water, thereby preventing a leak. Sometimes the float can get stuck in the wrong position in your dishwasher, and it can prevent your dishwasher from filling. Sometimes it can happen due to float valve and on other occasions due to float switch. Inspect the water hose coming to the dishwasher for any blockages. If the hose is not clogged then check the water inlet valve for any clogs, if the water will not even fill for few seconds then certainly the water inlet valve is bad and should be replaced. You can also use a multimeter to check continuity on inlet valve. If you don't get any value on the multimeter then you'll need to replace the water inlet valve assembly. However, if the valve is fine then the float switch assembly should be replaced. Hope this helps... Please post back if you need more information.

Daniel

Jul 21, 2011 | Siemens Dishwashers

Not finding what you are looking for?
Ariston Technologies LI640S Dishwasher Logo

Related Topics:

566 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Washing Machines Experts

Darren Moxam
Darren Moxam

Level 2 Expert

67 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

Are you an Ariston Technologies Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...