Question about Televison & Video

1 Answer

Great explanation!! Can I also get the IC's from Radio Shack? Or where... Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 8,617 Answers

Youre welcome. No you have to get the ICs at either or . has them cheaper They havce fast shipping usally 2-5 days . Let me know if you need any further Info.

Posted on Mar 01, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Radio Shack Multimeter, 22-168a, shunt resistor value????

Go to the Radio Shack site and you may with the model number find a schematic or you can email/contact them for the value of the resistor.

I predict it is a precision value and type you will have to get from them if available.

PS: you posted in wrong catagory as this is TV section.

Mar 12, 2012 | Televison & Video

1 Answer

Thanks for the reply about the convergance chip where can I pick one up up from the manufacturer or a radio shack ect.?

model number ? IC number ? and radio crack doesn`t sell convergence ic`s, get back to us with model or IC`s "stk #" video-tek

Jun 30, 2009 | Hitachi Televison & Video

1 Answer


I dont have the service manual for that model, However they are located right next to the convergence Ics and there will be quite a few and they will be all Identical should be about 8 to 10 resistors. If you can get me the board location number such as R356 etc, I can find out the rating. I would doubt that Radio Shack would have them as they are metal film usually anywhere from 1/2 up to 2watt resistors . But if you can locate the resistors near the ICs I can tell you the ratings if you give me the board location of one of the resistors.

Jun 16, 2008 | Apex Digital GB55HD09W 55" Rear Projection...

1 Answer

Need link and part number for STK-IC for AKAI PT4298 HD rear project convergence fix

The ICs you need are STK392-040 you will need two of them. You cant get the ICs or Radio Shack as they are specialty items. You can get them at the following link and they will provider free instalation instructions as well as free tech support just in case you need extra help. heres the link.

Jun 04, 2008 | Akai PT4298HD Rear Projection Television

1 Answer

Toshiba 42h81 - bad r7731, need replacement

radio shack should have that resistor. Another option is check with the tV repair shops locally. Most distributors will not sell 1 resistor but most TV shops will and radio shack may have it or can order it.

Apr 05, 2008 | Toshiba 42H81 42" Rear Projection...

2 Answers

Okay, I removed the circuit board with ease and was ready to operate and all the sudden I was stuck. The stk is attached to what looks to be a mine radiator and I have no access to clip the bottom of the...

use solder wick or a desoldering iron from radio shack which will **** up the solder so you easially remove the IC. Radio shack has a in-expensive desoldering iron with a rubber bulb which makes this easy.

Mar 28, 2008 | Televison & Video

1 Answer


Radio Shack should have the fuses you need just get the proper amp and voltage ratings. IC link fuses can be purchased at or

Jan 31, 2008 | Mitsubishi VS-50607 50" Rear Projection...

1 Answer

Converge semicoductor

with skill and experience. need solder wick or solder sucker(radio shack) screwdriver set, needle nose pliar, solder and solder iron 35 40 watts. desolder the IC all legs on bottom of pc board. pull the ic out with needle nose, install new ic ,u might have to bend and straighten the legs, dont force it. now solder all the legs carefully. GGGGGOOODDDD LUCK!

Aug 15, 2007 | Toshiba 42H82 42" Rear Projection...

1 Answer

Vertical lines

Get some freeze spray from radio shack then try placing a little spray on each chip on the video board and power supply board and each time you spray a chip look for the picture to clear up. When the lines go away you have located the bad IC.

Jul 09, 2007 | JVC HD-70G886 70" Rear Projection HDTV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69803 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6384 Answers


Level 3 Expert

63990 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides