Question about Panasonic KX-TG2357 Cordless Phone

2 Answers

Can not rec a dial tone, phone states no link to base move closer

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 569 Answers


If “No link to base. Move closer to base, try again.” is displayed
even when using the handset near the base unit, the handset may have lost communication with the base unit. You need to re-register the handset to the base unit.
• Make sure the base unit is not being used.
• Have both handsets and base unit nearby during registration.
• Follow steps 1–3 listed below. You have about 1 minute to complete them.
• Confirm the extension number of the handset which has lost the communication by placing the handset on the base unit or charger.
If you re-register the handset using the other handset’s extension number, the other handset will not function.
• If the handset beeps 3 times and “Error!!” is displayed, an error occurred. Try again from step 1.
• You can stop registration by pressing [OFF] on the handset, and pressing [LOCATOR/INTERCOM] on the base unit.

1 Base unit: Press and hold [LOCATOR/INTERCOM] until a beep sounds.
• The CHARGE indicator flashes.

2 Base unit: Press the extension number [1] (handset symbol 1 ) or [2] (handset symbol 2) of the
handset which has lost the communication.

3 Handset: Press and hold [FLASH/CALL WAIT] until “Handset Registering” is displayed.
• When registration is complete, a beep sounds from the handset and the display shows the number.
• Wait for 20 seconds after registration is complete while the handset establishes communication with the base unit.


• If the handset beeps 3 times and “Error!!” is displayed, an error occurred. Try again from step 1.
• You can stop registration by pressing [OFF] on the handset, and pressing [LOCATOR/INTERCOM] on the base unit.

Posted on Feb 23, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

I had this problem and the fix above did not work. In playing with the intercom function on the handsets - trying to use the base to connect to the handset as intercom - the phones connected!! Communication with the base was established - problem solved! This was AFTER I purchased another set of phones

Posted on Apr 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Panasonic KX - TG5664


may be the problem is with the speakers check that first

Jun 02, 2008 | Lands Phones

1 Answer

No dial tone it says no link to base,move closer,try again even when it is in the base


it needs to be registered with the base on phone go to menu scroll down til you see register, registration, register base, sect it, then it will tell you to set it on base, after that wait a few minutes til its done, pick up phone, you should now have a dial tone, also if you have your manual, look up how to registar base, it might be easier instructions there.

Dec 03, 2009 | Computers & Internet

1 Answer

My cordless phone says No link to base Move closer to base - I have no dial tone - do i need a new battery?


This is the usual message that the phone gives when the battery has died and it has lost connection with the base unit. The usual fix is to remove and reinstall the battery, then place the unit on the charger for a full charge. This will usually fix the problem that you discribed. If after a full charge, you still get that message, you will most likely need a new battery. Good luck...

Nov 06, 2009 | Panasonic Lands Phones

1 Answer

Cordless phone not connecting to base. no dial tone.


Hi,

switch the A/C mains off 5 minutes

or

Re-register them to the base,
This resolves the problem

Regards
Richard.

Apr 26, 2009 | Panasonic KX-TG5673 Trio Cordless Phone

1 Answer

Phones have no dial tone and a message that says


Unplug base (both connections) and re-plug them again. It works for me whenever this happens.

Mar 17, 2009 | Panasonic KX-TGA560M Cordless Expansion...

1 Answer

Model 25922 5.8 GHZ Cordless phone with one main phone and two extras


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Ge Telephone Solutions
Handset can not link.
• If any handsets become inoperable, place it on the main base cradle for 20 seconds to re-register.
No dial tone
• Check or repeat installation steps
• Make sure the base power cord is connected to a working electrical outlet.
• Make sure the telephone line cord is connected to the base unit and the modular phone jack?
• Disconnect the base from the wall phone jack and connect another phone to the same jack. If there is no dial tone on the second phone, the problem might be your wiring or local service.
• The handset might be out of range of the base. Move closer to the base.
• Make sure the battery is properly charged (for 16 hours).
• Ensure the battery pack is installed correctly.
• Did the handset beep when you pressed the TALK/CALL BACK button? Did the in use indicator come on? The battery may need to be charged.
http://www.home-electronics.net/ge/pc/IB/25922GE2_IB.pdf

Sep 02, 2008 | GE 26998GE1 Cordless Phone

1 Answer

I have a remote phone it does not have a telephone wire just an adapter. It is charged but I can not get a dial tone. It gives me the message "No link to base. Move closer to base,try again". What do I...


Place the phone in the base cradle for a minute and it should re initialize and solve your issue.
Good luck.

PS: By "Remote phone" I am assuming that you mean "Cordless"?

Apr 11, 2008 | Lands Phones

1 Answer

No link to base


put the phone in its base and then un unplug the phone for 5 seconds plug it back in and check for a dial tone.

Feb 20, 2008 | Lands Phones

Not finding what you are looking for?
Panasonic KX-TG2357 Cordless Phone Logo

996 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Lands Phones Experts

Ekse

Level 3 Expert

13434 Answers

martin hogg

Level 2 Expert

157 Answers

guyvstewart

Level 2 Expert

115 Answers

Are you a Panasonic Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...