Question about Vacuums

2 Answers

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie rd_wiebe@telus.net

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 701 Answers

You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htm
They are only 4.99 for a 2 pack. Plus they have $1.99 flat rate shipping where other site charge you up to $10.

Posted on Oct 17, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,673 Answers

Brushroll and belt will cost around $20

Posted on Feb 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The belt for the maain vaccume broke off and now with the new belt the roller will not work.


It sounds like your roller brush itself might be bad. Try holding the roller brush holding just the end caps with your finger tips, and spinning the roller. Does the roller spin freely? If no, this indicates that your roller brush's bearings have melted together. This is a common problem for Bissell vacuums, as they use cheaper plastic bearing caps. The roller brush is not covered under the warranty either.

When this part goes bad, this causes the belt to break almost immediately. If you tried replacing the belt, and it broke immediately, your roller brush has gone bad.

Here's a link to the Bissell LiftOff Revolution rollerbrush on our site;

Bissell Roller Brush for Lift Off Bagless

Please leave me some feedback, or rate my solution helpful if this helped you fix your problem. Thanks so much,

Chris Jones
GoVacuum.com

Jan 07, 2011 | Bissell LiftOff Revolution Pet Vac 37602...

1 Answer

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt...


sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set.

*An example of a brush roll*
086dc3d.jpg
Make sure that the brush roll spins freely.


Hope that helps.
Chris

Jun 09, 2010 | Bissell 3522 PowerForce Bagged Upright...

2 Answers

The vacuum cleaning brush is not spending


Yes belt probably broken. Also the brush roller heats up on the ends, causing the plastic end cap nearest the belt to melt/weld to the end. It's supposed to spin freely. Also 2 bearings inside tend to become sticky, probably from heat. Next thing you know, the brush roller is seized and will not turn. Probably the whole reason the belt breaks. New belt & new brush roller, 30-35 bucks. It will happen again. Now you've spent almost half what it costs new. Lose the junk. 2 years for a cheap vacuum is the normal life span anyhow.

Dec 10, 2009 | Bissell 37604 Lift-Off Pet Bagless Upright...

1 Answer

Brush wont go round but the belt is ok


The belt may look okay but it can still be stretched. If it is stretched it won't turn the brush against the resistance of the carpet. Here is a link to the belts you need and to the manual which has instructions:

Bissell Lift-Off Revolution Belt & Manual

Nov 23, 2009 | Bissell Lift-Off(R) Revolution(R) Turbo...

1 Answer

The brush is not working anymore


Your drive belt is probably broken. They usually need to be changed every 6 to 12 months. If you haven't replaced the belt recently I would try that. You can get the belts you need through this link and also view the manual which has step by step instructions on how to change the belt. hope this helps!

http://www.vacbelts.com/bissell-lift-off-revolution-pet-vacuum-belt-.htm

Oct 25, 2009 | Bissell LiftOff Revolution Pet Vac 37602...

4 Answers

Bissell Lift Off Broken Belt and Brush Roller


I had the same problem. I found that the brush actually melted to the end cap (the one with the square/ovalish end). I was able to pull it off with some force and applied some WD-40, but that only worked for one more use. The brush has again melted to the end cap and it is too deformed to try and fix. I suppose I will have to search for a new brush, but this model obviously has some innate flaws.

Feb 14, 2008 | Bissell Lift-Off(R) Revolution(R) Turbo...

1 Answer

Bissell Lift-Off(R) Revolution(R) Turbo Upright.


If you have a rubber smell, then the belt is slipping, does the brush roll turn freely while holding the ends? If not then replace it, part #2036619, if it is ok, then the belt has strectched and is slipping under load, part # 2106679, Style 8.

Jan 20, 2008 | Bissell Lift-Off(R) Revolution(R) Turbo...

2 Answers

Bissell Vacuum Cleaner


Did you check the brush roll? One of the ends of the brush may have froze and won't let the brush roll spin. If it is bad, then replace it.

Dec 21, 2007 | Dirt Devil M086700 Vision Bagless Upright...

Not finding what you are looking for?
Vacuums Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Roger Potts

Level 3 Expert

694 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...