Question about Televison & Video

1 Answer

Convergence\auto can the t.v be manually converged?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Yes...there should be an option in the setup menu to do that.

Posted on Feb 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a way to manually adjust the convergence on a Hitachi HDTV modol #43FDX15B?


Hi James,

If Auto Focus (Auto Convergence) won't complete the set-up stop trying to adjust it. There is a fault in the convergence circuit!! ICs have to be replaced and maybe some burnt resistors.

If you access the service set-up menu and try to adjust the "defective" circuit the Auto-focus may not work correctly after the IC's, etc are replaced. Experienced technicians know that the service menu allow easy resetting to correct the misalignment, etc. "First Time" technician can be easily misled, waste a lot of effort and never get a correct picture.

If you want to attempt the repair, buy the correct parts from a service guy that does this type of work. I suggest having the repair done by a local competent technician that is experienced with Hitachi Convergence Problems. It is considerably more challenging than changing a fuse.

Our Convergence Gallery shows a variety of Convergence Faults. If you live in Toronto, ON., Calgary, AB., or Vancouver BC. it costs $257 for Hitachi in home convergence repair.

Good luck.

Robert

Nov 17, 2015 | Hitachi Televison & Video

1 Answer

Have a 56" RCA that i had the user manual for and lost it. i used to do the manual and auto converge. its been so long i forgot how to access it. help?


press menu then scroll to setup the auto convergence features are listed there. If they have disappeared you will need the ITC222A convergence option missing repair kit available from www.tvrepairworld.com

Mar 17, 2010 | RCA R52WM24 52" HDTV Projection Television

1 Answer

52"projection tv colors overlap


Your convergence is bad. If after trying the Auto Convergence option on the TV it doesn't correct itself, you can try manually adjusting the convergence Here is a link to perform a manual convergence on your set. Good luck!
Greg
http://www.ehow.com/how_2034880_perform-convergence--tv.html

May 23, 2009 | RCA Televison & Video

1 Answer

The color green has come out of the other colors


Needs to be converged if this is a projection tv. Check menu for a cutomer convergence option. Should be a manual or auto convergence. If you cannot move anything in manual convergence then convergence amplifiers are bad and need to be replaced. Professional can replace no problem.

Apr 09, 2009 | Televison & Video

2 Answers

Convergence trouble


You most likley have bad convergence amps and two burnt resistors.Part# STK392-110.Convergence circut is located @ frot of set behind speaker grill.The only reset is in the customer menu listed Convergence reset.

Jan 12, 2009 | JVC AV-65WP74 Rear Projection Television

7 Answers

I hav a RCA model D52W25 its 52" it has convergence problems dont know how to setup the color things can u help??


Click on the following link :

http://www.riddledtv.com/repair/RCA.html. Go to the following section

RCA 52" D52W25 ITC222 rca_d52w25_small.jpg
(2) (3) (4)
(5) Stretched Image at top and bottom edge very distorted. Reheat all the surface mount solder points on the Small Signal Board. Then realign the set including convergence menu. To enter service mode: power off the set for 10 sec, then hold down Vol- and Ch- buttons for 10 sec. See this link: Alignment Procedure (pdf)


Also download the Alignment procedure pdf file. Hope this will help you. Please let me know if the information was of any help to you or you need further assistance.

Thanks

Oct 08, 2008 | Televison & Video

1 Answer

Convergence problem


http://www.retrevo.com/search/v2/jsp/mytrevo/myTrevo.jsp?page=man

You can download the manual here. Insrtuctions for auomatic convergence are described. I copied the instructions below.

Automatic Convergence
Your HD Monitor’s picture tubes might have been disturbed during delivery or
after you moved the HD Monitor, causing the color in your HD Monitor to be
out of alignment. The colors adjust by starting auto convergence.
IMPORTANT: Auto convergence works best once the HD Monitor has
warmed up for at least an hour. If you've just unpacked your HD Monitor,
it's a good idea to repeat the Auto convergence function when the
HD Monitor's been running for at least an hour. See page 38 for more
information about Auto convergence.
1. Press OK to begin auto convergence.
2. When the auto convergence is complete, the Red center convergence menu
appears. The cross in the middle of the screen should be yellow. If it is not,
use the arrow buttons to move the red cross to overlap the green cross.
Press OK when adjustments are complete.
3. The Blue center convergence menu appears with a cyan cross in the middle
of the screen. If it is not, use the arrow

Sep 23, 2008 | RCA R52WM24 52" HDTV Projection Television

2 Answers

Convergence prob for d52w26 rear projection tv 52"


If the auto-convergence is not working then the convergence amp ICs are starting to fail. If you can solder, try resoldering the pins on these ICs. If that fails to resolve the problem, replace the ICs. These are large black ICs attached to a heatsink and should be marked STKxxx.

Keep us posted.
Dan

Jul 14, 2008 | RCA P52926 52" Rear Projection Television

2 Answers

How can I do Auto Convergence on my 52" TV


The auto convergence should run automatically when activated, If it doesnt you will need to replace the convergence board.

May 10, 2008 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Sony KP-53HS30 Convergence Issue


Are both 3.15 amp fuses good ?................................T.

Dec 24, 2007 | Sony KP-51WS510 51" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69654 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6364 Answers

yadayada
yadayada

Level 3 Expert

63291 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...