Question about Mitel Superset 420 Corded Phone

1 Answer

No Sync When I plug up the phone it gives a "no sync" message. In addition, there is no dial tone.

Posted by on

  • eljay2 Feb 28, 2008

    by the way, the phone is a Superset 420

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 112 Answers

It is not connected to a digital port. Or bad port in phone system.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All phones are plugged in and operating but i get a busy signal on all in talk mode


I assumed when you say all phones are operating means there's power and are charging.
1. There could be some phones that are loading the Tel line. Disconnect all phones and plug it one by one while checking the dial tone. If all phones gives busy tone, there coulb be a problem in the Trunk line or the Tel Company line.
2. There could be a short or resistance in the line. Check the connection in junction box between your house and the Tel Company cable.
3. If you have an analog Tel set, you can check the dial tone directly from Tel Company cable that comes in to your house.

I hope this helps.
Best Regards.

Sep 01, 2015 | Panasonic KX-TGEA20 Additional Digital...

2 Answers

A few of our rooms has the voicemail light blinking. There is not a voicemail waiting and can not be cleared from the front desk or from the room.


Message Waiting Indicator Your phone's message waiting indicator is either a light or special tone that alerts you when you have voice mail.

Occasionally, the message waiting indicator may be out of sync with your mailbox. In that case, the indicator light or tone is ON but there are no messages waiting, or the indicator light or tone is OFF when there are new messages waiting.

To get the message indicator back in sync

  1. Save or delete all new messages
  2. Hang up.
  3. If the message indicator does not go out or stop within a few minutes, there may be a problem, and you should contact Verizon.
  4. If the message indicator does go out or stop, call your own number and leave a message
  5. Hang up and wait
  6. If the indicator light or tone does not come on within a few minutes, there may be a problem, and you should contact the vender.

Jun 08, 2015 | Phones

2 Answers

How do I get a dial tone?


Is the base station plugged into the phone jack on the wall?

May 17, 2014 | Swissvoice Epure Full Eco Cordless...

1 Answer

I have 2 problems. 1. The orange message light will not stop flashing no matter what I do. 2. Some how the system was switched from touch tone to dial tone. I can't seem to that switched either.


Resetting the voice message waiting indicator
When you receive a new voice mail message, the new message LED on the top of the handset flashes. In the event your message waiting light gets out of sync with your phone company's
voice messaging system, you can manually reset it back to the "No messages waiting" state.
1. Press and hold FiND on the base for five seconds.
Note: The handsets connected to the base will start to beep, however, keep pressing for five seconds.
2. A beep sounds and the message alert tone is reset.
Changing the dial mode
Your phone can communicate with the telephone network in two different ways: tone dialing or pulse dialing. These days, most base networks use a method called tone dialing, so your phone comes programmed for tone dialing. If your phone company uses pulse dialing, you will need to change your phone's dial mode. If you don't get a dial tone or can't connect to the telephone network, please follow the steps below to modify your phone's settings:
1. Press MENU/SELECT.
2. Select the Global Setup menu, and then the Dial Mode submenu.
3. Scroll to highlight Pulse.
4. Press MENU/SELECT. You will hear a confirmation tone.
If you ever need to change the dial mode back to tone dialing, follow the same procedure, but select Tone in step 3.

Finally for future ease of use, here is a link to the user manual were I copied the above information from:

http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/DECT1580-3om.pdf

Jul 21, 2011 | Uniden DECT 6.0 Cordless Phone ID

1 Answer

Both of my GE Dect 6.0 cordless phones, model #5-2811 say out of range or searching...out of the blue. How do I get my dial tone back???


Unlplug the power to all lines for 5 minutes, while waiting disconnect, inspect and clean the phone cords. Insert the phone cords back into the devices after 5 minutes of ALL devices being unpowered plug them all back in, Set each of the phones on the main receiver to "sync" them.

May 13, 2011 | Uniden Cordless Phone

1 Answer

No dial tone and I got the message " analyse en cours "


analyse en cours is french for analyze in progress.It might be that you have to re enter in the security code for the handset to sync up. also to change the language from french to english press feature *501

Jan 11, 2010 | NorStar T7406 Cordless Phone

1 Answer

I have charged for abt 20 hrs for set up. all I get is "Searching" Help me to move foreward.Sue DECT1560 This is a new phone I am trying to get it in service. I have no dial tone ,message "searching"...


First make sure the phone jack is working by plugging a working phone into it.

if it is working, use the same phone cable to plug into the base of your new unit.

if you do not get dail tone, place the handset into the main charging base. this should sync the phone up to the base. lift it out and try again.

if you still do not get dail tone or see searching, open the phone and remove the battery. wait 30s or so, plug the battery back in and set the phone in the main charger again. wait 10second and try the phone again.



Nov 06, 2009 | Uniden DECT15602 Cordless Phone

1 Answer

No dial tone


check for a line cord if it is connected to the line properly. and try to sync the phone with the base unit

Aug 17, 2009 | Uniden 5.8GHz Dual Cordless Phone

3 Answers

No dial tone


try pulling the batteries out for 24 hours and then putting them back in. It should reset all the software and it should sync back up.

Jul 25, 2008 | Uniden DCT646-2 Cordless Phone

2 Answers

Cant get one of the phone to get dial tone says unavalibel


All you have to do is put the phone that does not get a dial tone on the MAIN CHARGING BASE for 20 seconds! it will then sync up!

Good luck!

Jul 17, 2008 | GE 25931 Trio Cordless Phone

Not finding what you are looking for?
Mitel Superset 420 Corded Phone Logo

Related Topics:

401 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitel Phones Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

David Payne
David Payne

Level 3 Expert

13437 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

10628 Answers

Are you a Mitel Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...