Question about Philips 32FD9954 32 in. HD-Ready Plasma Television

2 Answers

Red light blinking

A red light is blinking on our plasma phillips tv. 3 short and one long..like morse code. lol. Cant get the tv to turn on at all. How do i fix this?

Posted by on

  • 4 more comments 
  • super gerry Mar 10, 2008

    a red light blinkig on our plasma 42fd9954/17s cant get the tv to turrn on at all.how do i fix this?

  • super gerry Mar 10, 2008

    42df9954/17s red light blinkig.

  • seedystevie Mar 16, 2008

    have a phillips 42in plasma with same red light blinking problem.

  • Marc R Mar 25, 2008

    Same problem

  • Anonymous May 20, 2008

    Hey folks, we bougth a 42 inch Phillips Plasma tv in 2004. Very nice quality picture, but about 3 years ago the blinking red light started. Has worked intermediately since then. Sometimes it works, others times no. Very frustrating.



    Six months ago, went out completely and after a month of trying just about everything, decided to replace it with an LG LCD tv that we bought in 06. The picture on the LCD is not as nice as the plasma. As I was unplugging and moving cords, I realized that the LG had a much heavier duty power cord than the Plasma. Tried the Plasma one more time (including plugging and unplugging, different outlets, etc), and still blinking. Took the cord off the LG, plugged into the Plasma and it worked. No problem since.



    So, at a minimum try switching out the power cord or buy a newer more heavy duty cord first. You can always return the cord if it does not solve the problem. Shame to throw away a 3K tv over a powercord. If this is really the problem, shame on Phillips for cheaping out.

  • Anonymous Dec 06, 2008

    32" plasma Monitor32FD9954


×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

My one take too long to turn on, relay/green light on and off for hours before it can start, I use a hair dryer to heat it up everytime, aim at the center from top, then it turn on very faster, no need to service

Posted on Oct 07, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

The blinking light is a POST (power-on self-test) diagnostic code indicating a serious problem preventing the TV from completing it's start-up. You may get the POST codes from your user documentation or sometimes the Mfrs website.

Posted on Mar 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i go to turn on the tv the red power light turns on and then starts flashing, with an all blank tv screen. I cant get anything but a black screen. The light will flash for a lil while, then the tv...


BLINKING RED LIGHT IS ERROR CODE.

1. Unplug set for a few minutes.

2. Plug back in and turn on.

3. When red power light starts blinking--COUNT THE BLINKS.

4. THREE BLINKS, pause, THREE BLINKS (ETC) IS SHORT PROTECTION AND A DO IT YOURSELF repair for some people. I have complete instructions for this repair.

5. 5 blinks, pause and 5 blinks etc is short on 140 volt line and while not as easy as 3 blink error code it points to places to look at.


If this told you something you did not know, rate this solution as very helpful as I do this here for free.

Post a comment here when you know what error code is and I will help.

REGARDS, SD TECH

Aug 16, 2010 | Panasonic PT-47WX53 47" Rear Projection...

1 Answer

Turning on my phillips tv the power button is blinking red


Plasma? Your power supply has bad capacitors. 3300uf most likely. This is a common problem on some Philips plasma TVs. Power board is located top center of the TV with the rear access panel removed. look toward the lower left portion of the board. If you notice any capacitors (they look like little plastic wrapped cans) with swollen tops or leaking dark fluid from the top of them, replace them. Myself, I always step up the voltage rating... ex: 3300uf, 10v -> 3300uf, 16v.

Mar 15, 2010 | Televison & Video

1 Answer

I have Dish Network Remote but there is no LG TV Code. How can I get?


8006
Thats a goldstar code and the buzz on the web is it works 50% of the time.

I just found this as well never tried it but it may work good luck

you want to know the code to put in just do these steps:
1. press and hold the tv button till the all the top buttons turn red
2. press the # button twice
3. the tv light will blink out the code to you. It will blink the first number then a pause then blink the 2nd number then a pause then blink the third number. For Sony2.gif you will see 5 blinks, pause, short blink, pause, short blink. (short blink means a zero) the code for sony is 500
4. Thats it!

Sep 14, 2009 | LG 50PX5D 50 in. Plasma HDTV

1 Answer

Tv wont turn on and automatically shuts down


I'm having the same issues with my phillips flat panel. I downloaded the firmware update from phillips and that helped...but only once. I'm back to the same issue this morning. But you might try this download...it may work for you.

Sep 06, 2009 | Philips 50PFP5332D 50 in. Plasma...

1 Answer

Tv lights blink, tv not turning on


HI, the fly back transformer has failed in your unit. this will occur if the dust level is high inside the set. the dust will settle on the cooper windings and, create an arch that will short out the entire power sector of this unit.

The fly back is usually the first to take the hit. replacing this will fix this issue.

Jul 11, 2009 | Televison & Video

2 Answers

Phillips Plasma - Model #42PF7320A/37 - 3 flashing red lights


it sounds like you could have a signal board problem they are pretty expensive but there is a web site that sells refurbed parts

Nov 17, 2008 | Philips 42PF7320A 42 in. Plasma HDTV

Not finding what you are looking for?
Philips 32FD9954 32 in. HD-Ready Plasma Television Logo

1,334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72271 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...