Question about EliteGroup PT800CE-A Motherboard

1 Answer

Pc problem when i turn on my pc it never turn on but the red light is still blinking like it was loading and no beep then my monitor was blank. what could be the main problem of my pc?pls help me tnx!!!

Posted by on

  • 2 more comments 
  • enigma pulp Feb 28, 2008

    no appearanca on screen and no beep

  • enigma pulp Feb 28, 2008

    pls help me with my problem

  • ghielbs May 11, 2010

    hi iwant to get a diagram of a motherboard

  • ghielbs May 11, 2010

    hi iwant to get a diagram of a motherboard

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Sounds like the power supply may need to be replaced.

Posted on Feb 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My pc dont show any thing axcept blank display with i tried to change graphics


Maybe one of your memory chips is bad.

If it seems to boot up all the way except the display is blank try the steps below:

Borrow a monitor from a neighbor, friend, relative or co-worker and connect it to the computer. If the Borrowed monitor display the desktop then the original monitor is bad, but the video card inside the computer is ok. If the Borrowed monitor does not display then the video card inside the computer is bad.

If it does not seem to boot up all the way try the steps below.

When you plug in the power cord is there any lights whatsoever on the laptop, where the plug goes in or on the AC Adapter of the power cord?

When you press the power button do you hear fans running, hard drive spinning, lights on the computer, hear any beeps or lights constantly blinking, hear the DvD/CD drive click and the light on the drawer of the DvD/CD turn on for a second or two? If so the computer is trying to boot or may have booted, but the screen is not showing for some reason.

Beep tones and blinking lights tells the technicians what is going on with the laptop and why it is not booting. Most times it's a motherboard issue when you hear beeps or blinking lights continuous. Most times the problem is with the memory or Video Card. Count the Blinking Lights or Beeps and take note of their pattern (1 Long or 1 Long followed by 2 Short).

Maybe you have a Static Charge Buildup. Remove the Power Cord, then Press and Hold the power button for 30 seconds. After 30 seconds plug the power cord back in and hit the power button to see if it boots.

Maybe your memory is bad or the memory slot is bad.

Remove the Power Cord, Open the Case and remove one of the memory chips. Set the chip aside then try rebooting the computer. If it boots, then you know the memory chip you set aside is bad so mark an x on it with an ink pen. If it fails to boot then move the chip to the next memory slot and try rebooting. If it fails take the chip out and set it aside, then put the other chip in and try booting it in both slots. If it boots, just to verify that the chip set aside is bad, mark an x on it and put it into the open memory chip slot and try booting.

Jun 07, 2012 | Intel Motherboards

1 Answer

When I turn on my pc monitor goes blank and computer starts beeping. As long as it's turn on it continue to beep. These are short often beeps


the beeps indicate a cpu or memory error. it would help to know what mb you have and if you replaced anything recently

Jan 29, 2011 | Motherboards

1 Answer

A computer with a D101GGC motherboard does not start. There is no beep or monitor singal. The fan is okay. As soon as the power is connected to the computer, the red drive access light comes on, but not...


its a common problem with intel D101GGC motherboard, just open the case and unplug the dvd power cable and data cable, then turn on the PC it will work fine.

Jan 09, 2011 | Intel D101GGC Motherboard

1 Answer

My PC gives no signal and a red light blinks


check first the Monitor if properly connected..check reset switch if in good not press...

check the beep soud of your PC while booting...if you heard 2 beeps sound try to remove the RAM the put it back but careful in handling it...and pls dont reverse the RAM pcb...
if continious beep ..try to remove the video card and put it back...
do this procedure your PC is off..


May 25, 2010 | Intel Motherboard

1 Answer

Pc Seems to be dead wont load bios post moust doesnt work or keyboard or monitor


I have the same problem, the CPU fan spins, keyboard lights blink, no start up screen, or bios.
But, when I push a few times on the pc reset button, then the CPU fan is becoming still, the keyboard light are out and I can start the computer again in a normal way.
Can this one be a temporally solution for you too? Do you have any suggestion about?
I guess it can be an electricity dysfunction of a wrong fixed cable.

Oct 15, 2008 | Biostar P4M80-M4 Motherboard

1 Answer

BEEPS


just reseat the memory modules it will fix the issue

Jun 07, 2008 | EliteGroup P4VMM2 Motherboard

1 Answer

Not run 1.1


There are a lot of things it could be. Is this a new build or some thing that you have been using that started acting up?. Start be removing all the cards in it that you don't need. Then remove all the cables from the drives. See if it will boot. If it does start adding the cards and drives one by one until you find the one that is causing the trouble. If it still don't boot then check out your cpu or power supply.

Feb 28, 2008 | EliteGroup PT800CE-A Motherboard

1 Answer

Not run


memory module need for clean
clean with student erasor
check your smps {psu}

Feb 28, 2008 | EliteGroup PT800CE-A Motherboard

1 Answer

Pc problem 2 with beep when it run


Hello Jake Ponce,
You could power your machine down, and open the case. Then making sure you are grounded to the case (to prevent ESD damage), I would reseat all socketed hardware and plugs, such as Memory and graphics cards, PCI slot devices, etc... Unplug and re seat everything (especially anything that has been manipulated recently), then close the case and power it back up. It's worth a try and could very well solve your issue.
Good Luck.

Feb 28, 2008 | EliteGroup PT800CE-A Motherboard

2 Answers

Problem


there are many things that can cause this, first obvious causes would be bad ram, dead mainboard or hard drive.. i say dead motherboard due to the fact you say there is no post beep on startup, easy way to tell, remove all the ram, and turn it on, if it squeels at you, you know the motherboard still at least is somewhat operational, next thing try replacing the ram.

Feb 28, 2008 | EliteGroup PT800CE-A Motherboard

Not finding what you are looking for?
EliteGroup PT800CE-A Motherboard Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top EliteGroup Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Mark Taylor
Mark Taylor

Level 3 Expert

728 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you an EliteGroup Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...