Question about Washing Machines

1 Answer

Washer does not extract water satisfactory

After competion of cycle laundr is wet

Posted by on

  • Anonymous May 24, 2008

    does not spin water out leaves clothes wet

  • craig carter May 11, 2010

    what kind washer is it

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 156 Answers

Not spining out ck door switches depends on the model washer you have

Posted on Feb 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WSM2480 Clothes Still Wet After Slow Spin Cycle


It's possible that the tub didn't drain properly in the allotted time and the remaining water is slowing your drum from coming to maximum extraction speed.

Jan 10, 2014 | GE WSM2420D Unitized Spacemaker Washer /...

1 Answer

Why won't my Maytag Washer extract water properly from clothing after going through the complete cycle?


Belt tension spring faulty, belt loose. Pump partly blocked, look for coin caught in hoses. Internal clutch failed in gearbox, replace gearbox. Gearbox pulley wrongly adjusted, remove pulley, re-grease, re-install with correct clearance.

Dec 18, 2013 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Has a new motor, add detergent, close door. Indicator says laundr


Hello, welcome to Fixya.

Based on your description I'd suspect something is in the pump or you're either...

a) using too much detergent, even too much "HE" will cause problems with the rinse & spin cycles.

b) the wrong type of detergent

These machines must have "HE" type detergent's added to them only. Non -"HE" will not allow them to spin to there potential, cause damage and sometimes not spin at all.

Here's how to check the pump...
If your washer is indeed a WFL2060, this is how to reach the filter and clean it.
( If it is not a WFL2060 as the post indicates, please let me know and I can provide assistance on another model as it pertains to you ).

**Unplug the washer from the dryer or wall, or turn off the 30amp breaker at the home service panel...safety first**

1) Open the small square plastic door at the right bottom of the washer.

2) Via the small hose drain any access water from the pump...this is where a wet/dry shop-vac comes in handy, or a shallow pan with a few towels works as well.

3) Then turn the pump insert/button trap counter clock-wise and pull out. Clean the trap out thoroughly running it under hot water and mild soap or your washer detergent and inspect inside the pump for any other foreign objects/obstructions.

4) Re-install the lint trap insuring it is good and snug/tight. Before closing up the small access door, run a short rinse spin cycle to check for leaks.

Let me know how you make out, or if you require further assistance.

Thank you for visiting "fixya", please take a moment to rate the info provided for you here.

Good luck.

macmarkus :)

Jul 06, 2010 | Bosch Axxis WFL 2060 Front Load Washer

1 Answer

What does the max extract feature do


If the washer is removing all of the water from the washer during the spin cycle it is likely working properly. Not an expert but I believe max extract causes the washer to spin for a slightly longer period of time in order to remove more water from the clothes. We use it regularly because our clothes come out to wet otherwise.

May 03, 2009 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

What will the Max Extract button do?


The max extract button will do an extra spin to get any & excess water out of the clothes. It is a good thing to keep on to help cut down on drying time. If you find standing water in the washer, it is possible the hose is NOT in the correct position.

May 03, 2009 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

Spins slowly in stackable washer dryer


sounds like your spin brake is not releasing when the spin starts

Jan 07, 2009 | Kenmore 98702 Stacked Washer/Dryer

1 Answer

No Spin Cycle


Your machine won't go into spin cycle most probably because it awaits for pump to start extracting water out of the basket. If the "Door Locked" light is on th an it means that either filter, pump or drain hose are clogged (unless pump burned). Turn off machine, unplug the machine, clean the filter, check for foreign objects inside filter and pump housing and finally check/unclog the drain hose.

Apr 23, 2008 | Maytag Neptune MLG2000A Front Load Stacked...

1 Answer

Spin Cycle Fails on Washer


This solution is 100% correct, change the : wax motor &control board.I'll be happy to guide you through this if you need me to.

Apr 23, 2008 | Maytag Neptune MLG2000A Front Load Stacked...

1 Answer

Admiral AAV8000AWW washer - clothes are wet after spin cycle...


may be a loose belt or a partial blockage somwhere.

Nov 09, 2007 | Admiral AAV7000A

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...