I am looking for aTV mechanic for my Philips TV Not working properly

Usual instructions.

Turn on the TV.

Find the code(s) listed for your Phillips TV and shown in the instructions provided with your remote. (If you don't have the instructions, look on the remote manufacturer's website).

On the remote, press the "TV" button.

Then press and hold the "setup" button until the LED blinks twice. Then let go (you atr now in yhe setup mode.)

Now enter the one of the Phillips TV code numbers you got from the instructions (or website.) This is often a three digit or five digit code. If performed properly, the LED should blink twice indicating it has accepted the code. (If it did not blink twice, folliw these steps again.)

Now aim the remote at the TV and press power. The TV should turn off indicating its programned properly.

Try other functions on the remote, sound up and down, change channel, etc. If all work, your done. If not there are usually several different codes listed for every TV, just go back and try them all, until you find the one that works all functions.

If your HS400ATV is not powering up even with a fully charged battery and you've already replaced the ignition switch, there may indeed be another module or component that could be causing the issue. Here are a few possibilities to consider:
1. Main Fuse: Check the main fuse for the ATV. It is typically located near the battery or within the fuse box. Ensure that the fuse is not blown and is making proper contact. A blown main fuse can prevent power from reaching the ignition switch and other electrical components.
2. Starter Solenoid: The starter solenoid is responsible for engaging the starter motor when you turn the ignition key. If the solenoid is faulty or not functioning correctly, it can prevent the ATV from powering up. Inspect the solenoid for any signs of damage or loose connections. Consider testing the solenoid or replacing it if necessary.
3. Kill Switch/Safety Interlock: Check if there is a kill switch or safety interlock feature on your ATV. These safety mechanisms are designed to prevent the ATV from starting under certain conditions, such as when the brakes are not engaged or if the ATV is not in neutral. Make sure these switches are in the correct position and functioning properly.
4. Wiring and Connectors: Inspect the wiring harness and connectors for any loose, damaged, or corroded connections. Pay close attention to the connections between the battery, ignition switch, and any other modules or components. Clean and tighten any loose connections, and repair or replace any damaged wiring or connectors.
5. Electronic Control Module (ECM): The ECM or other control modules could be a potential source of the issue. These modules control various electrical functions in the ATV. However, diagnosing and testing these modules often requires specialized tools and knowledge. It may be best to consult a professional ATV mechanic or an authorized dealer who can properly diagnose and test the modules if needed.
If you've checked these possibilities and the issue still persists, it is recommended to seek professional assistance. They will have the expertise and equipment necessary to diagnose and resolve electrical issues specific to your HS400ATV.

Go to source and highlight tv air then channel search

Have a look here? The site includes diagrams for any number of mechanicals including ATV. I am still checking and will add to post if I find anything more:

http://www.pccmotor.com/wiring-diagrams.html

Please let us know if helpful by clicking the button below, thanks!

(NOTE: the link image is generic – pls. see site and search your ATV!)

click start control panel administrive tools ,computer management ,device manager look through all of your devices if you see a yellow question mark?or exclamation mark ! or red x
right click to reinstall drivers or
if you can see your usb but its not working
ports(com&lpt)right click update driver
hopefully you will find the right driver here
http://download.driverguide.com/driver/SAA7130HL/Philips+Consumer+Electronics/d589691.html

http://members.driverguide.com/driver/detail.php?driverid=589691&action=winfo
hope this helps

try to insatll window vista's driver of zebronic

The tv tuner card is either damaged or not connected properly if the pci slot was not used for a long time use blower to remove dirt from the board and try again
Some times the shops may have accidentally exchanged the cd so look at the card and try to find any related words number (version ) and then search in google it may work

Driver you have is not compatible! try to down load a newest version!!! and look on sound manager if mute is off

you probably need a hotel master remote, i.e. the philips rc2573gr:

http://salestores.com/philipsr.html