Question about D-Link AirPremier DWL-2700AP 802.11g/b Wireless Access Point

6 Answers

How to probe the configuration or reset the 2700AP?

I am using a wireless mesh setup using DWL 2700AP, which is supposedly configured with a static IP 192.168.4.3/24
I set my machine in the same subnet (192.168.4.10/24) but I am not able to ping it.

How do I know what configuration the AP is set up with? Or is there a way to reset the AP to its default settings?

Thanks

Posted by on

  • 2 more comments 
  • Anonymous May 23, 2008

    I'm unable to find a reset button on my DWL-2700AP. How do I reset this thing...can someone help?



    Dino

  • Lennox Jones May 23, 2008

    I'm unable to find a reset button on my DWL-2700AP. How do I reset this thing...can someone help?



    Dino

  • Anonymous Mar 10, 2009

    how to reset the dwl-2700ap version A3 when you're unable to access via network

  • vier12001 Apr 14, 2009

    how do i configure my DWL 2700 AP to be a wireless LAN and set it to use DHCP supposing my IP Address is 192.168.0.50 and gateway is 89.76.15.133

×

6 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thanks for all the supprot...i tried your sugestion and did the same...i could now borwse internet but i cannot access the D-Link configuration website using 192.168.0.50...nothing is coming

Posted on May 07, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi there is problem on DWL-2700AP Version B with the new frame DWL2700AP.v320.rc157.tfp my ap web or telnet stop , so i try your solution the two switches labelled S3 and S4 located along the right long side with the antenna facing up (this is when the AP is opened). Power the AP up and use a flat item to press S4 down for about 30 seconds.

the ap work agine thanks

Posted on Jan 24, 2009

The D-Link support site states that the DWL-2700AP can only be reset to the factory default through the graphical interface. It can however also be done by opening the unit up and pressing a switch.
For the DWL-2700AP Version B, there are two switches labelled S3 and S4 located along the right long side with the antenna facing up (this is when the AP is opened). Power the AP up and use a flat item to press S4 down for about 5 seconds. 
This will reset the AP to the factory default settings.
Tempo

Posted on Sep 10, 2008

Remove 13 screws from the perimeter of the back side of the DWL-2700AP and pull the covers apart. On the inside along the bottom adjacent from where the network cable plugs in, you will find a reset button. It is next to the white plug that leads to the antenna. You will need a flat screwdriver or something thin and sturdy to wedge between the casing and the reset button. While the AP has power, press the button and hold it in for a few seconds then release. Give it a few minutes and the factory defaults should be restored. Default IP: 192.168.0.50, Default subnet mask: 255.255.255.0

Posted on Aug 29, 2008

Remove 13 screws from the perimeter of the back side of the DWL-2700AP and pull the covers apart. On the inside along the bottom adjacent from where the network cable plugs in, you will find a reset button. It is next to the white plug that leads to the antenna. You will need a flat screwdriver or something thin and sturdy to wedge between the casing and the reset button. While the AP has power, press the button and hold it in for a few seconds then release. Give it a few minutes and the factory defaults should be restored. Default IP: 192.168.0.50, Default subnet mask: 255.255.255.0

Posted on Aug 29, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 427 Answers

Restore it to default, with these things, if it wont work on automatic, then something is worng.

Posted on Apr 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a dwl-2100ap that was already configured in a network..so i wanted to use in other network..what i did is i reset it by pressing the reset button for more than 15 seconds.and i configured the...


Hi

Do not type the IP address and subnet mask, just click on obtaib the IP address automatically and obtain the DNS automatically. Because if you encode the IP and subnet mask, there would be conflict and let the internet explorer configure it automatically.

Please let me know if you need more help and please rate it if you believe that it might help you and others. Regards

Feb 27, 2011 | D-Link AirPlus Xtreme G DWL-2000AP...

1 Answer

Netgear access point cant open configuration page


Typically you should be using configuration software until a real IP can be setup and you either address it statically or turn on DHCP. As for the gateway and other information, on a wireless gateway, it should all be routed through the network. Also, I think you have to be wired to the WAP to access the config page, I don't believe it can be seen over the wireless connection as a security feature.

Aug 02, 2010 | NetGear WG602 54Mbps Wireless G Access...

1 Answer

I am setting up a D-Link AirPlus DWL-800AP+. I can use it as an access point or repeater, I need the repeater. I access the internet through a wireless signal that serves one floor of my building. I can...


You must be on the same subnet of the AP. Static your IP address to 192.168.0.29 with a subnet of 255.255.255.0. If it's hooked up to the same network you are, you should get in.

Oct 25, 2009 | D-Link AirPlus DWL-800AP+ 802.11b Wireless...

1 Answer

Sometimes i try to ping the wireless access point and i get the message 'Request time out',i receive this message even if im directly connected to the access point.what should i do


When you connect the computer directly to the access point, you might not be getting IP address on your computer.
You will need to assign a static IP address on your computer in the range of default IP address of the Access point.
Click Here for More info on access point

Oct 08, 2009 | D-Link AirPremier DWL-2700AP 802.11g/b...

2 Answers

DWL-2700AP reset default settings


Remove 13 screws from the perimeter of the back side of the DWL-2700AP and pull the covers apart. On the inside along the bottom adjacent from where the network cable plugs in, you will find a reset button. It is next to the white plug that leads to the antenna. You will need a flat screwdriver or something thin and sturdy to wedge between the casing and the reset button. While the AP has power, press the button and hold it in for a few seconds then release. Give it a few minutes and the factory defaults should be restored. Default IP: 192.168.0.50, Default subnet mask: 255.255.255.0

Jul 18, 2009 | D-Link AirPremier DWL-2700AP 802.11g/b...

1 Answer

Reset DWL 2700AP to factory defaults


Hi dear try to flow this tips it will help you
Administrator Settings
Administrator settings allow you to customize User Name and Passwords as an Administrator of DWL-2700AP. The default value of the Username is "admin" with no password entered.
Password
Enter a password in the Access Point Password field. Type the password again in the next field to confirm it. The Password is case-sensitive ("A" is a different character than "a",) and must be between 0 and 12 characters in length

System Settings
You may reset the DWL-2700AP back to factory settings by clicking on Restore Default settings.
Restore Default Settings
Choose Yes and click Apply to restore all Access Point settings to the factory default settings.

Thank you
Imran
Pls rank as possible

Apr 20, 2009 | D-Link AirPremier DWL-2700AP 802.11g/b...

1 Answer

How can i fix an ip adress conflict?


If you Router has DHCP running then please check that no any computer which you conect has Static Ip configured.

There are few viruses around as well which cause the ip conflicts in the networks...


Nov 27, 2008 | D-Link AirPlus Xtreme G DWL-2100AP...

3 Answers

Configuration


The best way to set this access point is to connect your computer directly to the device via Ethernet, disble the wireless adapter temporarily on the computer. Since this is just an access point and not a wireless router, it is not capable of providing your computer with an IP address because it has no DHCP functionality.

The IP address you mentioned is the deafault IP address of the access point, there is a posibility that the default IP has been change.

Do a reset on the access point then assign an IP address manually on your computer(i.e 192.168.1.x x- bein any number from 1 to 254 except 50)

Access the AP using Internet Explorer or Firefox, type http://192.168.1.50 on the address bar it should prompt you for a username and password(check you documentation for the default username and password for the access point)

Aug 09, 2008 | D-Link AirPlus Xtreme G DWL-2100AP...

Not finding what you are looking for?
D-Link AirPremier DWL-2700AP 802.11g/b Wireless Access Point Logo

Related Topics:

4,160 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Wireless Access Points Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

scramblepad
scramblepad

Level 2 Expert

66 Answers

Anthony Chiang
Anthony Chiang

Level 3 Expert

524 Answers

Are you a D-Link Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...