An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert who has answered 200 questions.
An expert whose answer got voted for 20 times.
Re: out of range
You can try removing signal cable from pc.If it still says "Out of range" most probably main logic card or interface board as it is known in the lcd monitor could be defective.If on the other hand removing the signal cable gives message No signal ,cable not connected,try connecting monitor to another working known pc.If it still doesn't work the interface board in the monitor is defective.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It can be failure inside the monitor, but try it with another PC first.
The possibilty can be poor DC in the power supply which will be the first thing to check or failed EPROM which nothing you can do unless you have the way to reprogram it.
If you are going to DIY and have proper tools and know safety precaution then please read on: Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums Post back what you see inside so we can guide you further and it will help out other people in the future also. http://en.wikipedia.org/wiki/Capacitor_plague http://www.badcaps.net Capacitors kit: http://lcdalternatives.auctivacommerce.com/
the lowest resolution is not always supported. by the range maybe referring to the frequency. change that, that should work. if you are not sure, look at your monitors manual, it will tell you resolution as well as frequency optimal settings
Make sure you have the latest version of DirectX and 3D glide installed
on your computer. You can also try adjusting the monitor frequency from
control panel to something a bit higher. That should help.
me know how it goes. If the solution worked, please rate a fixya, if
not, please post back before you rate , so we can troubleshoot further..
Also you can try lowering the ressolution in the game..
i do not know that but if it run under windows xp you can try in this way . if you click on windows start with mouse you have to reach control panel and after that there is (in classic diplay ) sound and peripherals , there yopu can try to check for the speakers if they are connected or not - i hope it was correct - delfo
I have been having the same problem with my hpvs17 monitor when i start to use my web browser on linux distros. Now, for the next few days i am going to try my system on a regular crt monitor. if the monitor does not crash, than i will have to say that the hpvs17 monitor has a defect.It seems that when i go online, while i am in the middle of searching something, the monitor just shuts off and i get "input signal out of range".
i also have the same problem dude,these f...ing view sonic doesnt support customers,specially for asia..........please help me ,i am very poor and i cant buy another one........please help me brothers........mail me firstname.lastname@example.org thank you and god blesses you all.........greets from sri lanka
This series of monitor has a bad habit of destroying it's capacitors. I have fixed two S762G monitors (almost the same as a S761) by replacing 2 bulged capacitors on the motherboard with new ones. They cost me 50 cents each (plus shipping of like 3 bucks) from digikey.com. Didn't carry them at my local Radio Shack, but they did have them on the shelf at my local Fry's. (about the same price as digkey if you include the shipping costs.)
I would look for any capacitors on the mainboard that have their aluminum disc top bulged up. That's a sure sign of a blown capacitor. Anyone with good soldering skills can replace those for you. (making sure to put them in the right direction for their polarity, and getting the correct rating/voltage/temp) The two caps I had to replace on my S762G's were C21 and C22 and they were both 1000uF 16v 105c high temp radial electrolytic capacitors. Make sure you get the exact same specs for your replacements as from your originals.
The typical symptom of the blown capacitor on this monitor is that it will power on a few seconds, showing the screen properly, then make a slight pop and the power light will go off, then it will come back on again, and do it over and over. Sometimes they will "Warm up" after a while and stay on, but that will only work for a short time (typically under a month or two). After that, the capacitors will be fried and need replaced anyway. Best to fix them right away, to prevent possible damage to other components.
The difference between this symptom and a typical inverter board failure is that the monitor will power cycle repeatedly. Inverter failures usually show up as the backlight only turning on for a second or two showing a good display, then going off and staying off until the monitor is manually power cycled, and if you look really carefully under good lighting you can still make out the display with the backlight dead.