Babylock Ellageo will not feed after using embroidery unit. It happened once before, then just started working. Will still embroider but won't feed on regular sewing.

The Baby Lock Ellageo embroidery machine doesn't have a reset switch, but you can try the following steps to troubleshoot the issue:

1. Turn off the machine and unplug it from the power source for a few minutes.
2. Plug the machine back in and turn it on.
3. Check the power cord and make sure it's properly connected.
4. Check the fuse and replace it if necessary.
5. Check the embroidery hoop and make sure it's properly attached.
6. Check the bobbin and thread and make sure they're properly inserted and tensioned.

If none of these steps work, it may be a problem with the machine's electronics, and you may need to take it to a Baby Lock authorized dealer for repair.

I am going round in circles 'anonymous'. I'll say at the outset ALL Babylock manuals can be found online. I can find Ellageo BLL, but not 3. I can Find Ellegante 3.

Full list

https://www.mrsewing.com/pages/manuals

Ellageo Plus

https://babylock.com/machines/100/ellageo-plus

and more

https://www.google.com/search?q=baby+lock+ellageo+esg3+manual

..

Recommend you type "Babylock ellageo esg" into the search engine of your computer, and you should find someone, especially a dealer, to help you find the parts you need.
God bless your efforts.

Perhaps this will help:

http://babylock.com/downloads/instructions/?Update_ID=38

http://babylock.com/support/FAQ/?FAQ=14

Baby Lock ellageo BLL Instruction And Reference Manual Error Messages

Try contacting BabyLock Support or ask a BabyLock dealer.

...

Hi, I hope this helps. If it doesn't post again.
"Check:
Place the sewing foot under the sewing foot
holder so that the pins of the foot snap into
the sewing foot holder when the presser foot
lifter is lowered.
Please check that the sewing foot is properly
engaged by raising the presser foot lifter."

Question: Are you using top feed? If so:
"For all sewing jobs with the top feed, only use sewing feet with Cutout at the back (OA, 1A, 3, 4)."

Embroidery foot Part No.: 98-694-840-00 will not work with top feed.

Also, except for eyelets, the darning foot can be used for embroidery.

I'm not sure what you're trying to do :) darn or embroider :); I'm not sure what mode you're working in either; embroidery mode?

Darning with straight stitch
Program 00
Fit darning foot No. 6.
Set the needle at its highest position by turning
the handwheel, and push the pin of the darning
foot fully into the hole of the sewing foot holder
slightly pressing the darning foot between thumb
and forefinger. When doing this, the guide fork
should place itself around the presser bar and the
wire must be behind the fixing screw.
Darning position:
Lower the presser foot lifter pressing it lightly to
the rear until it snaps into the darning position.
Important Only in this position you have the
optimum thread tension for darning.
• Place the darning work in the darning hoop.
• Lower the feed dog.
• Pull up the bobbin thread and hold the threads
when you start sewing.
• Now guide the fabric back and forth evenly;
the length of the darn will be set by the size of
the hole. As you are determining the stitch
length yourself while sewing with the feed dog
lowered, you should sew at an even speed.
When you have reached the width of the dam
aged area, darn over the damaged area again
from right to left.
This guarantees a durable darn.
TIP: The faster you sew, the easier and more even
the darning will be. It you are moving the workpiece
too slowly, small knots will appear on the
wrong side of the fabric."

Whether working with terry-cloth or woven fabric,
with the help of the darning foot and the pro
gram 02 you can embroider initials of your own
design

Drop the feed dog and insert the darning foot.
Put the machine into the darning position.

Spread the fabric in an embroidery hoop and
embroider in accordance with program 02.

Lower feed dog
If the feed dog is not lowered for embroidering, the
machine does not embroider when the foot pedal
is pressed and the message appea rs:
Lower feed dog
ok?
The feed dog must be lowered in embroidery
mode.

could have a problem with the motherboard, may need to have the machine checked

Each manufacturer have their own bobbins.......not interchangable

http://www.babylock.com/sewing/ellageo/
click on manuals and guides.  Hope it helps.

go see your local parts man. he will know what you need and he will have it there or he will need to order it.