Question about Sanyo DS24205 24" TV

1 Answer

24" flat panel Sanyo

I was picking up the tv and I accidentally pulled out the cable cord connector out of the tv. Is there a way that I can fix this myself. Looks pretty simple.

Posted by on

  • Anonymous Mar 22, 2008

    when i hit the power button to my sanyo tv it goes on for 2 seconds then shuts off. i believe this is now happening because i had the power cord plugged into a power strip. the power strip was hanging in midair and slowly pulled the power cord loose from the back of the tv. i could be wrong. any ideas?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

I would say that you have pulled the pcb towards the back of the casing causing the front power button to just fall short of pressing the internal switch in properly. Where the scart socket is at the back of the set, push it inwards and then attempt to press the power button in, on the front of the set.

Posted on Mar 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the reset button


Sanyo Service Menu - Factory-Reset.com

factory-reset.com/wiki/Sanyo_Service_Menu
Jump to Sanyo TV Service Menu Method 2 - Unplug the power cable. Press and hold the {VOL -} button on the TV while plugging the power cable back ...

Sanyo TV reset button location? ' Yahoo Answers

https://answers.yahoo.com/question/index?qid...
Jul 27, 2007 - Does anyone know where to find the reset button on a 32" Sanyo TV? The thing is just totally dead and I am thinking maybe if I push the reset it ... I have a Sanyo TV, I accidentally hit the reset button twice. I ...
Aug 6, 2012
36 inch sanyo tv won't change off video 2?
Apr 17, 2010
I accidentally hit the 'reset' button the remote of my sanyo tv ...
Jan 6, 2010
Sanyo DS32224 TV Problem!!?
May 21, 2009
More results from answers.yahoo.com

Nov 29, 2015 | Sanyo DS31520 31" TV

2 Answers

Coax connector is broken off-how can i replace the connector?


You can pick up a chassis mount F connector here...you will need someone with basic soldering skills to replace:
http://www.electronix.com/rca-connector-p-13010.html

Oct 21, 2010 | Samsung TXG2548 TV

1 Answer

I accidentally hit the reset button on my sanyo tv and now i can't do anything it just says not antana push channel up to search, we dont have it hooked up to cable just to watch dvds


If you are using only in AV mode, this should not cause you this
problem. select AV mode and use.

You can refer to the user manual.

Aug 23, 2010 | Sanyo DS24425 24" TV

2 Answers

Sanyo 24" flat DS24425 suddenly turned off, won't turn on. Pressing the power button either results in no response or it turns on for a second, then turns off again. No picture. Already tried playing...


Solution to the won't turn on or turns on and turns off in 3 seconds thing...as my Ds24425 did.

First thing is very important...unplug the TV and let it set for 24 hours before you proceed.

The voltages inside a TV are EXTREMELY HIGH and LETHAL....so proceed with caution!

Place the set face down on a towel on a table and remove the back cover....hex screws around the perimeter and 1 phillips screw near the inputs.
The main board will slide up and out. unplug the degausing coil "white plug with two wires" and the speakers connector. This will make it easier to turn the board and take a look.

What I found with mine was a bad electrolytic capacitor. You can identify I bad cap "capacitor" by examining the tops of each one for bulging or signs of overheating "melted or bubbled plastic covering." The cap in question was C626 with a value of 1000uf, 16volt. I replaced with a 1000uf, 35volt and it works perfectly. The cap is located about center of the board. Carefully unsolder the cap and remove, make sure to install the new cap with the proper polarity...the board is marked with a dot indicating the negative lead of the cap.
Be sure to reattach the white plug and speakers connector and slide the board back into the plastic grooves. Then replace the back cover and test. Good luck! ...Daddio

Feb 02, 2009 | Sanyo DS24425 24" TV

1 Answer

Sanyo DS24205 24'' TV Not Recieving Signals.


Ok, cable connected is good. Can you move tv to another connection or run another cable from a working source. Maybe go into setup of tv and check input.

Nov 17, 2008 | Sanyo DS24205 24" TV

1 Answer

Sanyo tv making high pitch noise from loose cable connector


The noise is coming from the fly-back transformer. By moving the cable connector you move the main board. Unplug the TV and remove the back. The transformer has a red wire going to a rubber cup at the top of the picture tube. Looking at the transformer you will see a dough nut shape with a metal piece going through it .. Drive some tooth picks between the dough nut and the metal core. That should reduce or stop the ringing.

Apr 21, 2008 | Sanyo DS31520 31" TV

1 Answer

Sanyo Flat-Screen CRT Parental Controls


try giving sanyo a call at 800-877-5032

Nov 21, 2007 | Sanyo DS24425 24" TV

2 Answers

Sanyo TV is stuck on Video screen


Universal Remote should do it.

Sep 08, 2007 | Sanyo DS24205 24" TV

2 Answers

TV Cable connector issues, Evil Dog


but is the TV still repairable? yes it just a simple problem call tech he will do it at your home in a short time.

May 04, 2007 | Sanyo AVM-3659S 36" TV

2 Answers

Problem with brand new TV


The reason you're getting a blue screen is that you're not getting a signal. Newer TV's have this "blanking" feature to "kill" the snow in the absence of a signal. Check the connector at the end of the cable where it screws onto the set. Stargazer

Feb 04, 2007 | Sanyo DS24425 24" TV

Not finding what you are looking for?
Sanyo DS24205 24" TV Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sanyo Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69878 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Are you a Sanyo Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...