Question about Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Washer continues to drip into tub after cycle in complete.

After the wash cycle completes, water continues to drip into tub.
My wife plays with timer to get it to quit.

Posted by on

  • Anonymous Mar 29, 2014

    at end of wash cycle water still remains in bottom of washer

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Maytag Master
  • 2,651 Answers

Contstant water dripping into tub sounds like a bad water valve, no repairing valve just replace it

Posted on Feb 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an MAV7600 Maytag washer the hot water fill valve drip after the cycle complates


if the washer keeps taking water and even when the washer is on the off position.
The problem could be a bad water valve.

Mar 15, 2012 | Maytag MAV7600 Top Load Washer

2 Answers

Water leaks (drips ) into tub after cycle/spin is complete


You have a bad pressure switch or the small hose connecting to the pressure switch may be bad

If the washer leaks water when is filling only, check the following: 1.Fill hoses
2.The water mixing valve

3.Filling injector ( If your washer uses one )
4.Filling spout


If the washing machine leaks during the wash cycle, check the following:
1.The pump
2.The tub stem & seal
3.Tub to pump hose
4.The drain hose
5.Tub (rusted holes)
6.The drum support bolts


If the washing machine leaks during the spin cycle, check the following:
1.The drain hose
2.The tub cover seal
3.The pump
4.The pump hoses

5.The stem & seal
6.The drum support bolts

Feb 10, 2008 | Maytag LAT2300 Top Load Washer

1 Answer

Washer continues to fill but never washes, as if a valve has not closed and the water just keeps drianing out of the damned thing.Crappy washer, havent liked it since i bought it.


A defect in the water-inlet valve may mean that it's no longer able to shut off completely when the electricity has been turned off to it. If this occurs, the valve may leak and drip water into the clothes tub. In time, the water may accumulate substantially. If this happens, you need to replace the valve.
A defect--or an obstruction--in the water-level switch may mean that it can't tell the water to shut off. So the machine overflows. This switch senses the water level in the clothes tub. It's usually a diaphragm device with a small, clear tube attached between the switch and the bottom of the washer's outer tub. As the water level in the tub increases, the pressure on the air in the tube increases. When the pressure reaches a certain level, it activates the switch, shuts off the water, and signals the timer to begin the agitate cycle. You can either clear any obstruction in the tube or replace the water-level switch.

Jan 23, 2011 | General Electric WJRE5500GWW Front Load...

1 Answer

The water, there was no water left in the tub of the washer, but the clothes were dripping wet; and the cycle was showing to be complete. I had to re-set the dial to the spin setting inorder to completely...


What has happened is that your water pump has gone out and it cannot pump the water out of the washers tub. This is a common issue and replacing the pump is not that hard assuming you have the time, effort, tools and energy.

Jan 23, 2011 | Kenmore 24962 Top Load Washer

1 Answer

Water continues to drip into the tub even after all cycles have completed. my tub is filling up with water, I have turned off the water to the machine but it continues.


The water inlet valve needs to be replaced. It's not shutting off the water completely. It's located where the water hoses connect to the washer.

Oct 09, 2010 | Maytag Washing Machines

1 Answer

My frigidaire front load washer will start a wash, complete the first cycle but then stop and flash all the lights and beep continously until I press "start" or "cancel". If I press "start" again it just...


Hello there:
If your cycle does not complete or The cycle doesn't advance
When the cycle should advance, it's probably the timer or a cold-water supply problem: It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer. It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. than check the cold water supply line and the filter

Aug 15, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Water continues to drip and fill tub after wash cycle completes


Your water inlet valve where the water supply hooks up to the washer is not sealing good.It can get sediment in it and cause this. Having a well for water supply can cause this more than water that has time to settle.

Sep 02, 2009 | Maytag PAV2300 Top Load Washer

1 Answer

Incomplete wash cycle.


It sounds as if you have something acting as a flap causing the restriction. You should take the hose that leads from the tub to the pump off and see if there is anything just inside the tub. I have noticed that alot times you could have a coin that blocks the opening. You may have to remove the inner tub to remove anything in there

Dec 30, 2008 | Maytag SAV3655A Top Load Washer

1 Answer

Whirlpool washer continuouse water water runninng into tub


try turning the mach off while it is spinning and filling.if it continues to fill or drip heavy,the mixing valve is not closing completely and needs to be replaced.if the water stops when the mach is turned off,there is a problem with the pressure switch.

Sep 28, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

Not finding what you are looking for?
Maytag Atlantis MAV6000 Top Load Washer Logo

488 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4636 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...