Question about Vacuums

1 Answer

Vacuum cleaner hi.this is 10 yrs old and not overly worked.bags are changed regularly and the micro filter has been changed at least three times over ten years.it goes well for about 2o minutes then loses power with not much "suck"after that.sometimes shutting down completely,because of overheating i presume,or just carries on at a much lower'"suck".have tied shaking bag inside but no luck.any suggestions out there or can you tell me the agents support office for new zealand[auckland].many thanks.

Posted by on

  • james croad Feb 26, 2008

    aeg vampyr 8209 electronic thanx

  • mp1797 Jan 24, 2009

    The Temp Light came on and vacuum wouldn't ****. Shut off the vacuum and unplugged it. Waited a few mins. and tried again, but vacuum wouldn't run...only the Temp light comes on.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 75 Answers

What brand vacuum is it?

Posted on Feb 26, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Are bags needed for a dirt devil hand held dust buster?


Dirt Devil Parts

dirtdevil.com/parts/

Dirt DevilNo promo code required. ... most popular: Bags: Belts: Filters: Cleaning Solutions: Filters, F1-F85: Filters, Adapters: Filters, ... vacuum cleaner: Attachments & Tools: Brushrolls, Hand Vacs: Brushrolls, Uprights ... Handheld Steam Cleaners.

Type G (10 Pack) - 3010348001 - Dirt Devil

dirtdevil.com/parts/details/3010348001/type-g-10-pack/

Dirt DevilGenuine Type G bags. Fits all hand vac models equipped with the paper bag adapter. Includes ... The Handheld Vacuum That Picks Up Where Others Leave Off ...

Ultra Corded Bagged Handheld Vacuum - Dirt Devil


Jan 01, 2016 | Dirt Devil Vacuums

1 Answer

As I was vacuuming my vacuum cleaner stopped working


Hi, it's Allie from Crucial Vacuum!

Your Hoover Windtunnel may have stopped working for several reasons. First, make sure that your unit is properly plugged into an electrical outlet and make sure the electrical outlet is working correctly. Vacuum units, and other appliances, protect themselves from sudden electrical charges, ups and downs. Make sure the electrical fuse and breaker are on, if not reset breaker.

Some units may heat up and will automatically shut themselves down to prevent fires. Allow your unit to cool down for 30 minutes while the thermal protector is automatically reset. Overheating, may have been caused by a clogged hose, dirty filters, full bags or a roller brush that is not running properly. All these situations compromise the unit's air flow and make the unit work harder, making it to heat up.

To avoid these situations and to keep your unit running at it's maximum capacity, make sure to change filters regularly (recommended every 3-6 months), clean your brush roll from any tangled hair strands or debris monthly (roller brushes are recommended to be replaced at least yearly), and replace belts every 6 months.

You can purchase direct your replacement belts, bags, roller brush and filters from Crucial Vacuum with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10

http://www.crucialvacuum.com/hoover-windtunnel-self-propelled-roller-belts.html

http://www.crucialvacuum.com/vacuum-bags/hoover-type-y-paper-bags-18pk.html

http://www.crucialvacuum.com/hoover-40110006-three-layer-final-filter-2pk.html

I hope this was helpful. If you would like further assistance, please feel free to give us a call at 877.750.9239. We have helpful and friendly customer care representatives on the line ready to assist you.



Alejandra (Allie) Sepulveda-Rivera
Crucial Vacuum Customer Care
http://www.crucialvacuum.com

Oct 04, 2014 | Hoover U6437-900 / U6439-900 Windtunnel...

1 Answer

Since I replaced the bag in my Eureka Rally 2 (this was the first time) the suction has not been working well. Could you please tell me what I could have done incorrectly. Thankyou


The dust bag holder is an important part of this vacuum. Make sure the bag is installed into the holder sliding bag collar into slots to secure.
Make sure the bag is tucked into cleaner. or the bag cover will not latch securely.
Also, the motor and exhaust filters should be cleaned at each bag replacement.
REPLACING THE FILTERS
Filters should be cleaned or replaced when they become visibly soiled or suction power is reduced. Always operate the cleaner with the filters installed to avoid motor damage. The dust bag must be changed and the filters cleaned or replaced if the window of the Clean Filter Indicator changes into red when the cleaner is operating at maximum power and the nozzle is raised from the floor.

Mar 28, 2011 | Eureka Vacuums

1 Answer

My 30 year old canister vac has had both the filter and bag changed, but everytime I turn it off the bag compartment opens and ejects the bag.


I think its time for a new vacuum cleaner.....sounds like the circuitry is malfunctioning or you have an airflow problem that is tricking the vacuum into thinking the bags full. check all hoses and airways for blockage

Nov 14, 2010 | Electrolux Guardian Bagged Canister Vacuum

2 Answers

Kenmore canister vacuum will not turn on


No, the only effect of not cleaning them would be decreased air flow and consequently . The time between changing filters depends on how much the vacuum cleaner is used. Common failures are damaged cords and a damaged or failed power switch

Mar 29, 2010 | Kenmore 23513 Progressive Bagged Canister...

1 Answer

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space...


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove one component at a time until the suction returns. eg turn on and feel suction under floor head - not good? then remove the rod, then the hose.
Once at the machine on its own it gets a little triky as i don't know which model you have. However if you have a bagged model remove all the filters and the bag and retest. There will be at least 2 filters, one before the motor and one after (maybe under the vacuum or right at the back). If it is a bagless model even though the filter may look clean it is probably blocked with very fine dust. If suction returns when the filter is removed then you need to buy a new filter. I am a nilfisk vacuum cleaner agent so i can supply a filter for you.
If this still doesnt help you are welcome to call me if you live in australia my contact details are on my website www.nelsonvacuums.com.au.
Hope this helps !.
Happy vacuuming :)

Aug 23, 2009 | Vacuums

1 Answer

Vacuum just stopped working.


is there a filter in it if so clean the filter.try it without the bag in it.make sure the bag is in correctly.does the bag expand when you turn it on.you might have something caught up in the hose.take the hose off and blow througfh it.if you can't its clogged.also check the inlet where the dirt goes into the bag.the inlet might be clogged.please leave feedback

May 04, 2009 | Electrolux EL7020A Oxygen 3 Ultra Canister...

1 Answer

Numatic Henry Micro HVR-200


motor is over heating. you need to clean bag, filter and hose first then re test

Aug 21, 2008 | Numatic Henry Bagged Canister Vacuum

Not finding what you are looking for?
Vacuums Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Roger Potts

Level 3 Expert

694 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...