Question about Dyna-Glo Double Tag-a-long Heater

1 Answer

Dnya glo RMC-95-c2 parts needed

I have an older kerosene heater and I need some parts. The 1 800 number on the unit doesn't connect to dnya glo anymore. Can you help me?

Posted by on

  • Shihlin22 Dec 30, 2008

    I also need a part-the wick adjustment knob. The company closed up in July can not find parts yet.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 181 Answers

The number i have for them is 847-324-3753 let me know if it helps

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to see pictorial instruction on how to replace wick in a Dyna Glo RMC-95-C2 kerosene heater


I think the Dyna-glow RMC95 series of heaters are equivalent to DH2300 series heaters.
In any event, the wick you purchased should have ahd the installation instructions included with the wick.

If it didn't or you tossed it, Here's a link to the DH-2300 series heater's Owners Manual, which may help you.

http://www.yourheater.com/DH2301-3%20owners%20manual.pdf

Good luck. Be sure to wear rubber gloves when you try to install the wick. Particularly, if you still have kerosene in the tank.

Feb 11, 2011 | Dyna-Glo RMC-8001SS Heater

2 Answers

I just replaced the wick, cleaned up the heater and filled with new K-1 kero. The heater (Dyna-Glo RMC-95-C7) is emitting black smoke worst than ever. The wick is burning a little unevenly.


Either the wick was improperly installed or you may not have allowed enough time for the wick to soak in the kerosene and become evenly distributed. Check the placement of the new wick and allow time (several hours) for the wick to absorb the kerosene.

Jan 31, 2011 | Dyna-Glo RMC-8001SS Heater

1 Answer

Have a Dnya-Glo RMC-KFA210T has problems igniting and is pouring fuel out the front of the burner area,could the pump be bad


We havethe exact same model, that had the exact same problem. We took the topcover off and there is a small rubber hose that feeds air from the filter intake to the fue3l mixture. We discoverdthe rubber hose had cracked so wasn't fitting tightly so not allowing the proper amount of air to the mixture. We put a new rubber hose on it and started rigvht, been working fine ever since!

Jan 23, 2011 | Heaters

1 Answer

I have a 3000btu dnya glo unvented gas fied room


I'm not familiar with these heaters but I assume there is button or something you push to get the pilot to light. There will be air in the pipe between where the gas comes in and the pilot light. You have to give it enough time for the gas to push this air out of the line. Hope this helps.

Mar 13, 2010 | Dyna-Glo D-E37 Wall Mounted Panel Heater

1 Answer

Have a Dyna Glo RMC-95-C2 and I can't get it to lite.


You have to change the batteries.. the manufacturer shipped it with **** batteries.

also take it apart.. very simple and clean out any soot..

Soot will cause heavy smoking...

The wick should last more than a year ....

Dec 14, 2009 | Dyna-Glo RMC-8001SS Heater

1 Answer

Kerosene heater


Dyna Glo 95 c4 Manual
http://www.owneriq.com/mdownloads/8979e0af-dfee-45f1-a8ba-c05c2f5ed4a8.pdf

Jan 31, 2009 | Dyna-Glo RMC-8001SS Heater

Not finding what you are looking for?
Dyna-Glo Double Tag-a-long Heater Logo

Related Topics:

455 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dyna-Glo Heaters Experts

paulcarew

Level 3 Expert

1898 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

drifterray

Level 1 Expert

10 Answers

Are you a Dyna-Glo Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...