Question about Hitachi UltraVision CineForm 55VG825 55" HDTV

1 Answer

Hitachi 55vf820 problem

The tv will not respond to any functions other than on/off, volume control, pip, and last channel from the remote. the only sidepanel button that functions is power. It is stuck on last channel viewed. No response with remote or buttons on TV. please help

Posted by on

  • hmirwvu Mar 18, 2008

    no, the buttons are fine.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 306 Answers

Most likely the buttons on the tv are stuck or malfunctioning, replacment of the button pannel will solve the issue

Posted on Mar 17, 2008

  • cory casper
    cory casper Mar 18, 2008

    Then its the connectors to the buttons, either way its something to do with them if its doing what you say they are.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error message on screen that says PO 1.15 V100


The error is likely to be from the satellite as the set model listed does not have that kind of error.

Nov 29, 2012 | RCA P52926 52" Rear Projection Television

1 Answer

How do i switch it to hdmi with universal remote???


U can't switches to the HDMI modes with the universal remote,because universal remotes it have very basic functions only like Off/ON channels up and down volume up and down mostly it,this is far more functions then the universal remotes controls can do.Tries websites like Remotes.com,Tvrepairworld.com to buy an exact remote to the tv original DLP tv remote.

Jan 15, 2011 | Hitachi 65F59A Television

1 Answer

My projection hitachi tv has a blank square showing up on the upper left hand corner. it shows up on all tv channels, but is fine when using DVD. What is the problem?


Sounds like you have Picture in Picture enabled. It doesn't show when viewing DVD because the DVD is the PIP. Just turn PIP off, there should be a button for it on the remote.

Nov 24, 2009 | Hitachi 51F500 51" Rear Projection...

1 Answer

Pioneer SD-582HD5 - screen went black, no sound, Poor remote feed


The blue tube might be leaking coolant in the high voltage area, that is the cause of the POP. This repair might not be a DIY because of the lethal high voltage surrounding the CRTs tubes.
The slow response from the remote could be because the coolant has affected the main board where the IR signal are going to the remote sensor.
Let me know if you require further assistance.

Dec 20, 2008 | Pioneer SD-582HD5 58" Rear Projection...

1 Answer

How do you get to diffrent tv station to show at the same time (pip)


If your TV has built-in Duel Tuner then you can see 2nd picture in pip. In remote you have channel up-down button for main picture and another set of channel up-down for pip function to change channels in pip.

Sep 28, 2008 | Projection Televisions

1 Answer

Hitachi 55vf820 problem


Will not turn on. TV is pluged in its almost like a power surge. The power bar is lit so for some reason the tv is not getting power.

Mar 17, 2008 | Hitachi UltraVision CineForm 55VG825 55"...

1 Answer

PIP stuck


MrKevin, some Hitachis have 2 different pip buttons on the remote, I believe 1 says pip mode or something to that effect, do the rest of the functions on your remote work? Check and see if you have a second pip button and be sure the remote is set to "tv" if it has that little slide button on the side, good luck, hope this helps

Nov 27, 2007 | Hitachi 50EX01B 50" Rear Projection...

2 Answers

Problem with PIP Function


To turn off PIP. Use tv menu and auto set channels, once searching for channels, turn off and PIP will be gone. If you can't access auto program tune tv to channel 3 and try again.

Nov 24, 2007 | Sony KP-53V75 53" Rear Projection...

1 Answer

Set top box and remote control


I have the same problem. When I move the 8300HDC away from the TV, or power off the TV, the remote responds. There seems to be some kind of RF interference, which makes no sense since the TV shouldn't emit RF, and the the box should be using IR only for remote input. My TV is a 46" LCD Samsung. Try turning off the TV and see if the 8300HDC responds to powering on and off with the remote.

Sep 16, 2007 | Hitachi 51F710 Rear Projection Television

Not finding what you are looking for?
Hitachi UltraVision CineForm 55VG825 55" HDTV Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hitachi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...