Question about Kitchen Ranges

Open Question

Stimpson Grinder Model 411

I have a old meat grinder made by Stimpson It is a model 5622 I need the complete grinder head I have the knifes and plates I just need the head and worm can you tell me where I can find these Idems thank you

Posted by on

  • 3 more comments 
  • lcosborn Oct 29, 2008

    i need the same thing

  • atvfan2000 Nov 14, 2008

    I need cutters, any luck?

  • Dennis Blucher
    Dennis Blucher Nov 07, 2013

    Are you still looking for the head to the grinder stimpson model #5622

  • Dennis Blucher
    Dennis Blucher Nov 07, 2013

    i know a guy that has one he is selling

  • Dennis Blucher
    Dennis Blucher Nov 07, 2013

    the throat and blade clamp is broke

×

3 Suggested Answers

bigg t
  • 640 Answers

SOURCE: Meat slicer

Goto http://www.hobartcorp.com/default.aspx and call your local branch.Im a service tech for hobart and i can tell you there is ( little if none) these parts are availiable any longer.I will look around for you.

Posted on Feb 24, 2008

rickead1
  • 1998 Answers

SOURCE: I have a Saeco Model

this is a programing issue refer to your manual on the start time and stop time of how long the grinder runs and how many beans it puts in there is a section on stop and start time on page 22 check how much is set for each beverage the higher the number the more is thrown into the cup here is your manual if you dont have one to refer to if you have any questions message me back thanks again Rick

p.s Used to do vending for 10 years with 100 of these I dont miss those days at all lol
also had 1200 bottle and can vendors and 400 snack vendors

your manual http://www.alcor-holding.ro/documente/8P-en.pdf

Posted on Jan 14, 2011

  • 552 Answers

SOURCE: Is it possible to get

Hello,

This is a tough question, if any one can these guy's should be able to help you, click on the link below.

Gearbox Drawing

Posted on Mar 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a berkel meat slicer which the blade wobbles on ,


Hi and welcome to FixYa, I am Kelly.

Most models have a bearing, washer and spacer that are support the knife/blade in the head housing. The parts are cheap and not to difficult to change.

Parts catalogs can be loacted using this link:

https://my.vulcanfeg.com/resourcecenter/vulcanwolfberkel/ProductDocumentation/Forms/ViewAllPartsCatalogs.aspx

You can use the following link to locate a distributor near you:
http://www.berkelequipment.com/Berkel/Service/

Without a model number I used the 823-827 series models as a reference here:
https://my.vulcanfeg.com/resourcecenter/vulcanwolfberkel/ProductDocumentation/F43190.pdf

Thanks for choosing FixYa,
Kelly

Mar 14, 2011 | Kitchen Ranges

1 Answer

Is it possible to get some drawing of gearbox bearings need replaycing on hobart mixer grinder model no 4346


Hello,

This is a tough question, if any one can these guy's should be able to help you, click on the link below.

Gearbox Drawing

Mar 01, 2011 | Kitchen Ranges

2 Answers

How to remove fuel pump 1995 camaro z28 5.7


If you have a Fuel pump blown and needs replacing you probably have been quoted approx $220 for the pump and about $450 labour and about 6 hours of work.
Due to its location you would have been informed that suspension, exhaust, support bars etc have to be removed before the tank is removed then the pump removed right?
Here's what I did, I removed the back carpet, I then drew a cut out area central on the flat of the highest point on the body pannel and cut a wide hole, leaving one section attached for folding back down later. My position was perfect, I unscrewed the pump and replaced it with the new unit.
I cut the plate with a drill to start, then I used tin snips to complete the cuts. {NO GRINDER or OXY}
I folded down the flap and sealed it, I then got 2 galv plates from home depot {$0.80 each} and screwed it over the top, then sealed the edge and sprayed it with a can of black paint. Looks like a factory access area.
Took me 55 minutes all up, and saved me $450. I have pics available

Nov 29, 2009 | Dacor Epicure ERD30 Dual Fuel (Electric...

1 Answer

Need to replace knobs on Frigidare stove model #FGF316ASB


Go to searspartdirect.com. Type in your COMPLETE model number and use the part locator illustrations on the following page. There should be a complete listing of part numbers for you to order on line. They should be listed under the "Backguard" heading as items number 32 and 36. Part numbers 316102303 and 316009009, respectively. I hope this helps you.

Aug 04, 2008 | Kitchen Ranges

1 Answer

Auto oven cleaner


I removed the two screws that hold the warning plate that has the latch coming through it. This allows the oven lock lever and latch to move around. you will see the shiny base of bracket that holds the lever and latch mechanism. I took a plain butter knife and pushed back the insulation to see the switch. I then put the butter knife against the switch and rapped it fairly hard with the screwdriver handle 3 or 4 times. Put the plate back and screws back. Turned on the breaker and was good as new.

Tools needed.. butter knife and nutdriver to fit screws.

Jul 10, 2008 | Kitchen Ranges

3 Answers

Meat slicer


Goto http://www.hobartcorp.com/default.aspx and call your local branch.Im a service tech for hobart and i can tell you there is ( little if none) these parts are availiable any longer.I will look around for you.

Feb 23, 2008 | Kitchen Ranges

1 Answer

Meat probe button on control pad


there is no real way to reset it you reset it when you turned the breaker off, It sounds like the EOC (electronic oven control) is faulty. I would just keep reset it and keep doing that to bake the turkey how hot will it get before it buzzes? is it showing any error codes?? F1, F2, F3 etc.....

Sep 30, 2007 | Jenn-Air JES9860 Electric Kitchen Range

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

806 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

yadayada
yadayada

Level 3 Expert

63661 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...