Question about Audio & Video Receivers

1 Answer

Have durabrand ht 395, no sound from center channel, connections ok, center speaker works

Posted by on

1 Answer

I have my center channel not working on my yahama rx-v793 i try every thing but its not working.

Posted on Oct 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No sound from center speaker or subwoofer on HT-R500 av receiver


Take a left or right speaker that you know works and connect it to the center and test. Repeat for the sub.

Are you sure you setup the AVR correctly that it knows you have a center and sub?

Aug 16, 2014 | Audio & Video Receivers

2 Answers

In dolby digital mode i can not get any voice volume. All other sounds are ok


Assuming that you mean Dolby digital 5.1, confirm that you have a center channel properly connected and perform the following;

Using the remote, enter the menu on the receiver and navigate to the selection labeled "LEVEL." Toggle through the selections until you reach the "CENTER CHANNEL". You will be able to use the remote to increase the volume of that channel in .5dB increments.

Feb 01, 2011 | Denon AVR-589 Receiver

1 Answer

Sony STR-DH510 Multi-channel AV receiver connected to cambridge soundworks ensemble IV w/ passive subwoofer: no sound from center channel during viewing, or during speaker level test- all other speakers...


The STR directs sound to the center as instructed by its speaker setup. You say the center does not work on calibration. Is it defined?

Prove another speaker does or does not work on the center output. Then we'll know if it's the receiver or the speaker ensemble that has the problem.

Have you checked the manual for this "
There is no sound, or only a very low-level sound is heard from the center/ surround. "?

Aug 03, 2010 | Yamaha DSP-A1 Receiver

1 Answer

Yamaha RX-V365 Receiver when I hook up my center channel it is not audible at all. The R and L speakers work fine when they were located in the FRONT A and FRONT B terminals, but when I moved everything to...


With what signal did you try? Maybe your signal source (DVD/TV or radio) didn't contain any sounds for the center channel.
Go to the Setup menu, Speaker setup / Manual setup and find there item called "Test tone". It will output a test tone to each speaker individually (you will see on LCD which speaker is being tested at each moment). If you will hear a sound from the center now, there is no issue and center is working fine, just your source didn't contain any sound for the center.

If it doesn't work, then either you have faulty cable, faulty speaker or faulty center output of the receiver.
- Try connecting the center speaker to different output of receiver (this will test if speaker is OK).
- Try connecting working LEFT speaker to left output with CENTER cable (this will test if cable is OK).
- Try connecting working LEFT speaker with working cable to the CENTER output (this will test the output of receiver if OK - but use the Test Tone from Setup).

May 18, 2010 | Yamaha Rx-v365 A/V Home Theater Receiver

2 Answers

Onkyo TX-DS696 receiver center channel not working


Can you say explicitly that the Center Channel speaker is defined as something other than NONE?

And how does dialog sound? If it sounds ok you're routing it to the front speakers. This is from the manual...

"For ideal Surround effects, all speakers should be installed. If a
center speaker or subwoofer is not connected, the sound from the unused channel is properly distributed to the connected speakers in order to produce the best Surround sound possible."

Apr 10, 2010 | Audio & Video Receivers

2 Answers

Lux Audio 5.1 home theater speaker & Yamaha HTR 5540 AMP


configure ur PC (both OS audio and third party sound driver) for surround sounds. control panel- sounds and audio devices - speaker settings - advanced - speker settings. so this done. make sure u select the 6 input channel - the button is on the right edge near the volume knob. near the vol button there are two buttons for selecting input type with up down arrow. from that u can select the input type this will be indicated on the top front indicator. but with the 6 input channel selected all selections are preceeded. if u select stereo mode u will have left/ right audio only.
make sure u connect the input right. connect from computer to 6 channel input. main, surround, center and sub-woofer.  connect the spekers to main (L/R), rear(surround) (L/R), center and sub woofer to terminal marked sub woofer ouput. this done select like i said before the 6 channel button. that should do it.

Mar 13, 2010 | Yamaha HTR-5540 Receiver

1 Answer

Kenwood VR 505 low sound in center channel


if the cables are ok and the speaker are ok also beside good setting you will have a problem of the output stage in your receiver.

May 06, 2008 | Kenwood VR-505 Receiver

1 Answer

Dialogue - Not Audible


The dialogue comes from the center speaker. If you have a center speaker make sure that that it is connected correctly. If it is them check the speaker configuration setup menu. Make sure that the center channel is set to small. If it is set to none you will get no dialogue. If you don't have one make sure that it is set to none. Make sure that you have the speaker levels set correctly according to the manual. Lastly check the tweeter in your center channel is not blown.

Oct 23, 2006 | Onkyo TX-DS989 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68157 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...